PIDA, PIFA and Koser’s reagent: what each one does in synthesis, and which to choose
Share
PIDA, PIFA and Koser’s reagent: what each one does in synthesis, and which to choose
The reactions of each reagent, from alcohol oxidation to the synthesis of iodonium salts, with the conditions and yields reported in the literature
PIDA, PIFA and Koser’s reagent are metal-free iodine(III) oxidants whose reactivity resembles that of heavy-metal oxidants. This guide describes the reactions of each reagent, from alcohol oxidation to the synthesis of iodonium salts, with the conditions and yields reported in the literature, and explains which reagent to use for each reaction.
Contents
- Overview of the reactions
- 1. Alcohols to aldehydes, acids, lactones and nitriles: PIDA with catalytic TEMPO
- 2. α-Functionalisation of ketones: Koser’s reagent and PIDA
- 3. Phenols: oxidative dearomatisation with PIDA or PIFA
- 4. Electron-rich arenes with PIFA: radical cations, azidation and biaryl coupling
- 5. Primary amides to amines: the Hofmann rearrangement
- 6. Nitrogen transfer: sulfoximines, isoquinolines and C–H amination
- 7. Heterocycles by oxidative cyclisation
- 8. Alkenes and alkynes
- 9. Radical reactions
- 10. PIDA as the oxidant in palladium catalysis
- 11. Iodonium salts and iodonium ylides from PIDA and Koser’s reagent
- 12. Deprotection, oxidation of sulfides and cleavage of diols
- 13. Choice of reagent, handling and work-up
- Products in this article
PIDA ((diacetoxyiodo)benzene), PIFA ([bis(trifluoroacetoxy)iodo]benzene) and Koser’s reagent ([hydroxy(tosyloxy)iodo]benzene, also called HTIB) are iodine(III) compounds. In each, iodine is bonded to a phenyl group and two oxygen ligands (Scheme 1).
Scheme 1. The three reagents with their CAS numbers, formulae and molar masses. The structures are drawn T-shaped: the two oxygen ligands and iodine are approximately collinear.[109]
Hypervalent iodine reagents react in a similar way to heavy-metal oxidants.[106] They are widely used because they are mild and selective oxidants, environmentally benign and commercially available.[108]
The sections are ordered by substrate or reaction type, from alcohols (section 1) to the choice between the three reagents (section 13). Each section gives the conditions and yields reported in the sources, a table of practical points and its main conclusion in bold. Yields of single examples are marked as such. A general scheme shows a transformation without a specific yield.
Shorthand used in this article:
- TEMPO: 2,2,6,6‑tetramethylpiperidin-1-oxyl
- TFE: 2,2,2‑trifluoroethanol; HFIP: 1,1,1,3,3,3‑hexafluoropropan-2-ol
- Ts: tosyl (4‑methylbenzenesulfonyl); OTs: tosyloxy
- Boc: tert-butoxycarbonyl; Fmoc: 9‑fluorenylmethoxycarbonyl; PMB: p‑methoxybenzyl
- equiv: molar equivalents; rt: room temperature
Overview of the reactions
| Transformation | Reagent | Co-reagents and conditions | Section |
|---|---|---|---|
| Alcohol to aldehyde or ketone, and further to carboxylic acid, lactone or nitrile | PIDA | TEMPO (catalytic); more PIDA and water for acids; ammonium acetate for nitriles | 1 |
| Ketone to α-tosyloxy ketone, converted in one pot into α-azido ketones, thiazoles and other heterocycles | Koser’s reagent | Acetonitrile at reflux, or dichloromethane | 2 |
| Ketone to α-hydroxy dimethyl acetal | PIDA | Potassium hydroxide in methanol | 2 |
| Phenol to quinone monoketal, p‑quinol, spirolactone or masked o‑benzoquinone | PIDA or PIFA | The nucleophile determines the product: methanol, water or a carboxylic acid in a side chain | 3 |
| Electron-rich arene to aryl azide or benzylic azide | PIFA | Trimethylsilyl azide; HFIP for the ring, acetonitrile for the benzylic position | 4 |
| Two arenes to a biaryl, without a metal | PIFA | Boron trifluoride etherate, low temperature | 4 |
| Primary amide to amine (Hofmann rearrangement) | PIFA | Acetonitrile–water, mildly acidic | 5 |
| Primary amide to methyl carbamate, urea or ammonium tosylate | PIDA or Koser’s reagent | PIDA with KOH in methanol (carbamate) or with ammonia (urea); Koser’s reagent (tosylate) | 5 |
| Sulfoxide, sulfide or sulfinamide to NH-sulfoximine or NH-sulfonimidamide | PIDA | Ammonium carbamate in methanol, open flask | 6 |
| Indene to isoquinoline (nitrogen-atom insertion) | PIDA | Ammonium carbamate in methanol | 6 |
| Carbamate or sulfamate ester to oxazolidinone or oxathiazinane (C–H amination) | PIDA | Rhodium(II) acetate (catalytic), magnesium oxide | 6 |
| Oxidative cyclisation to oxadiazoles, triazolopyridines, benzothiazoles, hydroxy lactams or isoxazolines | PIDA or PIFA | No metal; mostly at or below room temperature | 7 |
| Alkene to syn or anti diacetate | PIDA | Boron trifluoride etherate, with or without water | 8 |
| Alkene to syn ditosylate; exocyclic alkene to ring-expanded ketone | Koser’s reagent | 95% methanol for the ring expansion | 8 |
| Alcohol or carboxylic acid to a radical: remote C–H functionalisation, iodides, acetates, Minisci products | PIDA or PIFA | PIDA with iodine and light; PIFA with blue light | 9 |
| Directed C–H acetoxylation, carbazoles, alkene aminoacetoxylation | PIDA | Palladium(II) acetate (catalytic) | 10 |
| Arene, arylboronic acid or terminal alkyne to iodonium salt | Koser’s reagent or PIDA | TFE or HFIP for thiophenes; boron trifluoride etherate for boronic acids | 11 |
| 1,3‑Dicarbonyl compound to iodonium ylide, then cyclopropane | PIDA | Base for the ylide; rhodium(II) acetate (catalytic) for the cyclopropane | 11 |
| Dithiane to carbonyl compound | PIFA or PIDA | PIFA in aqueous acetonitrile or aqueous methanol | 12 |
| PMB ether to alcohol | PIFA | Nitroxyl radical catalyst | 12 |
| Sulfide to sulfoxide | PIDA | Potassium bromide (catalytic) in water | 12 |
| 1,2‑Diol to aldehydes; alkene to carbonyl compounds | PIDA | Dichloromethane; osmium tetroxide (catalytic), NMO and 2,6‑lutidine for alkenes | 12 |
The reactions described in this article and the section for each. The conditions are those of the examples in each section, not general recommendations.
1. Alcohols to aldehydes, acids, lactones and nitriles: PIDA with catalytic TEMPO
PIDA alone does not oxidise a simple alcohol. Benzyl alcohol did not react with PIDA after 12 hours at 35 °C, but with a catalytic amount of TEMPO it was oxidised rapidly to benzaldehyde (Figure 1c).[3] With TEMPO, PIDA oxidises primary and secondary alcohols to aldehydes and ketones at 0 °C to room temperature, in an open flask and in most common solvents.[1]
TEMPO is the catalyst and PIDA is the stoichiometric oxidant, so 10 mol% TEMPO and a small excess of PIDA are sufficient. In the Organic Syntheses procedure, 32.5 mmol of nerol is oxidised to neral with these amounts in acetonitrile and pH 7 buffer at 0 °C. The reaction is complete in about 20 minutes and gives neral in 87–89% yield (Figure 1a).[1] The Z double bond of nerol, which isomerises easily, is retained.[1]
Figure 1. Oxidation of alcohols with PIDA and catalytic TEMPO. (a) Nerol to neral; the Z double bond is retained.[1] (b) A Boc-protected amino alcohol to the amino aldehyde in flow, with no loss of optical purity.[3] (c) Control experiment: benzyl alcohol is not oxidised by PIDA alone, but it is oxidised by PIDA with TEMPO.[3] The yields are those of single examples.
The oxidation is selective for primary alcohols. According to the Organic Syntheses procedure, they are oxidised to aldehydes with very high selectivity, even in the presence of secondary alcohols and other oxidisable groups, and without noticeable over-oxidation to the carboxylic acid.[1][2] Many sensitive protecting groups are tolerated.[1] In a flow study with 1.1 equivalents of PIDA and 10–20 mol% TEMPO in dichloromethane at 35 °C and a residence time of 4.5 minutes, no carboxylic acid was detected.[3]
Boc-protected amino alcohols give the corresponding amino aldehydes. In the same flow study, N-Boc-(S)-phenylalaninol gave the aldehyde in 52% yield with no loss of optical purity, whereas N-Boc-(S)-phenylglycinol gave the aldehyde in 40% yield with partial loss of optical purity (Figure 1b).[3]
Role of water
A kinetic study published in 2026 examined the oxidation of benzyl alcohol by PIDA and TEMPO in acetonitrile at room temperature.[4] The rate is first order in PIDA and in water, and zero order in TEMPO and in acetic acid, the by-product formed from PIDA (Table 1).[4]
Water is required for the reaction. The study reports that adventitious water, that is, the traces present in the solvent and reagents, is sufficient, so no water has to be added.[4] The rate increases as water is added and shows no saturation in the range tested.[4] The rate was independent of the TEMPO concentration in the range tested.[4]
| Species | Order in the rate | Range tested | Practical meaning |
|---|---|---|---|
| PIDA | First order | 0.16–0.176 M | The rate is proportional to the PIDA concentration. |
| Water | First order, no saturation | 0–0.16 M | Added water accelerates the reaction; adventitious water is sufficient for it to proceed. |
| TEMPO | Zero order | 1.6–3.2 mM | In this range, more TEMPO did not accelerate the reaction. |
| Acetic acid | Zero order | 0–0.08 M | The acetic acid formed from PIDA does not slow the reaction. |
| Benzyl alcohol | Partial positive order | 0.12–0.16 M | – |
Table 1. Kinetic orders for the oxidation of benzyl alcohol by PIDA and TEMPO in acetonitrile at room temperature.[4]
The study also proposes a new mechanism (Figure 2). In the classical mechanism, the oxoammonium ion TEMPO⁺ oxidises the alcohol, and PIDA only re-oxidises the hydroxylamine TEMPO–H. The 2026 study proposes two coupled catalytic cycles.[4]
In the first cycle:[4]
- water replaces an acetate group on PIDA (rate-determining step 1);
- TEMPO⁺ oxidises this iodine(III) species to an iodine(V) species;
- the alcohol binds to the iodine(V) species (rate-determining step 2);
- the iodine(V) species oxidises TEMPO–H back to TEMPO⁺ and is itself reduced to iodine(III);
- this TEMPO⁺ oxidises the iodine-bound alcohol to the aldehyde, and iodosylbenzene is released;
- acetic acid converts iodosylbenzene back into PIDA.
In the second cycle, PIDA oxidises TEMPO–H to TEMPO⁺ and is reduced to iodobenzene.[4]
Figure 2. Mechanism of the PIDA/TEMPO oxidation. (a) The classical mechanism, in which TEMPO is involved in every step. (b) The mechanism proposed in the 2026 kinetic and computational study, simplified: intermediate structures are omitted, and the boxes give the oxidation state of iodine.[4]
The Organic Syntheses procedure already includes water, as pH 7 buffer, and with 1.1 equivalents of PIDA the oxidation still stops at the aldehyde.[1]
The rate depends on water and not on TEMPO. For a slow PIDA/TEMPO oxidation, the kinetic data therefore support adding a small amount of water, not more TEMPO.
Further oxidation: carboxylic acids, lactones and nitriles
With more PIDA and a small amount of water, primary alcohols are oxidised further to carboxylic acids. This method is used to prepare nucleoside 5′-carboxylic acids from protected nucleosides.[5] In the example of Figure 3a, a 3′-O-TBDPS thymidine is oxidised in dichloromethane with 0.23 equivalents of TEMPO and 2.2 equivalents of PIDA. After two hours a few microlitres of acetonitrile–water (1:1) are added, and after a further 24 hours the 5′-carboxylic acid is isolated in 100% yield.[6]
Diols are converted into lactones. 1,5-Diols with one primary and one secondary hydroxy group give δ-lactones with catalytic TEMPO and excess PIDA.[7] 1,6- and 1,7-Diols give seven- and eight-membered lactones with 10 mol% TEMPO and 2.5 equivalents of PIDA in dichloromethane at room temperature (Figure 3b). The yields reported in the table of that paper are 40–100%, and one 1,7-diol gave the hydroxy aldehyde instead of the eight-membered lactone.[8] For one diol in that study, silver carbonate on Celite, PCC, TPAP/NMO, Dess–Martin periodinane and IBX were also tested, and PIDA/TEMPO gave the best result by a clear margin.[8]
With ammonium acetate as the nitrogen source, TEMPO and PIDA convert aliphatic, benzylic, heteroaromatic, allylic and propargylic alcohols into nitriles in one pot. The alcohol is oxidised to the aldehyde, the aldehyde forms an imine, and the imine is oxidised to the nitrile (Figure 3c).[9]
Figure 3. Further oxidation with PIDA and TEMPO. (a) A 3′-O-TBDPS thymidine to its 5′-carboxylic acid; the acetonitrile–water is added after two hours.[6] (b) A 1,6-diol to the seven-membered lactone, under the conditions of the source; the yield range is that of its table.[8] (c) Primary alcohols to nitriles with ammonium acetate.[9] The yield in (a) is that of a single example; (c) shows the general transformation.
Nucleoside 5′-carboxylic acids can also be prepared electrochemically, with 4-acetamido-TEMPO as the mediator in water–acetonitrile and without a stoichiometric chemical oxidant.[10]
Practical points
| Point | What the sources report |
|---|---|
| TEMPO | 10 mol% in the Organic Syntheses procedure.[1] In the kinetic study, the rate did not depend on the TEMPO concentration.[4] In the flow study, the reaction was incomplete with less than 5 mol% TEMPO.[3] |
| PIDA | 1.1 equivalents for the aldehyde;[1][3] 2.2 equivalents for the acid in Figure 3a;[6] 2.5 equivalents for the lactones in Figure 3b.[8] |
| Solvent | Acetonitrile with pH 7 buffer; dichloromethane and most common solvents are also suitable.[1] |
| Water | Required for the reaction; added water accelerates it.[4] |
| Heat | The reaction is slightly exothermic: an ice bath is used on a larger scale but is not required at 1–5 mmol.[1] |
| Acid-sensitive aldehydes | The aqueous phase should be neutral. Neral isomerised on distillation, so it was purified by chromatography.[1] |
| α-Amino aldehydes | N-Boc-phenylalaninal was obtained with no loss of optical purity; N-Boc-phenylglycinal with partial loss.[3] |
| TEMPO after the reaction | TEMPO is removed before chromatography, because it is not separated on the column.[1] |
With catalytic TEMPO and 1.1 equivalents of PIDA, primary alcohols are oxidised to aldehydes; with more PIDA and water they are oxidised to carboxylic acids. The same reagents convert diols into lactones and, with ammonium acetate, alcohols into nitriles.
Products: PIDA · TEMPO · 4-Acetamido-TEMPO
References (section 1)
- G. Piancatelli, F. Leonelli. Oxidation of nerol to neral with iodobenzene diacetate and TEMPO. Org. Synth. 2006, 83, 18. doi:10.15227/orgsyn.083.0018 (open access)
- A. De Mico, R. Margarita, L. Parlanti, A. Vescovi, G. Piancatelli. A versatile and highly selective hypervalent iodine(III)/2,2,6,6-tetramethyl-1-piperidinyloxyl-mediated oxidation of alcohols to carbonyl compounds. J. Org. Chem. 1997, 62, 6974–6977. doi:10.1021/jo971046m
- N. Ambreen, R. Kumar, T. Wirth. Hypervalent iodine/TEMPO-mediated oxidation in flow systems: a fast and efficient protocol for alcohol oxidation. Beilstein J. Org. Chem. 2013, 9, 1437–1442. doi:10.3762/bjoc.9.162 (open access)
- M. Bingham, T. R. Pradhan, D. Bhattacherjee, R. Alkahtani, P. Kavanagh, T. Wirth, P. Dingwall. Revealing the mechanism of TEMPO-hypervalent iodine(III) oxidation of alcohols. J. Am. Chem. Soc. 2026, 148, 8852–8862. doi:10.1021/jacs.5c21609 (open access)
- J. B. Epp, T. S. Widlanski. Facile preparation of nucleoside-5′-carboxylic acids. J. Org. Chem. 1999, 64, 293–295. doi:10.1021/jo981316g
- M. E. Jung, A. Toyota. Preparation of 4′-substituted thymidines by substitution of the thymidine 5′-esters. J. Org. Chem. 2001, 66, 2624–2635. doi:10.1021/jo001223a
- T. M. Hansen, G. J. Florence, P. Lugo-Mas, J. Chen, J. N. Abrams, C. J. Forsyth. Highly chemoselective oxidation of 1,5-diols to δ-lactones with TEMPO/BAIB. Tetrahedron Lett. 2003, 44, 57–59. doi:10.1016/S0040-4039(02)02489-9
- M. Ebine, Y. Suga, H. Fuwa, M. Sasaki. Highly efficient synthesis of medium-sized lactones via oxidative lactonization: concise total synthesis of isolaurepan. Org. Biomol. Chem. 2010, 8, 39–42. doi:10.1039/B919673K
- J.-M. Vatèle. One-pot oxidative conversion of alcohols into nitriles by using a TEMPO/PhI(OAc)2/NH4OAc system. Synlett 2014, 25, 1275–1278. doi:10.1055/s-0033-1341124
- D. J. Abrams, M. R. Johnson, C. R. Lacker, T. P. Yoon, J. R. Martinelli, S. S. Stahl. Mediated electrochemical oxidation of nucleosides to their 5′-carboxylic acid derivatives. Chem. Eur. J. 2025, 31, e202500713. doi:10.1002/chem.202500713
2. α-Functionalisation of ketones: Koser’s reagent and PIDA
Koser’s reagent introduces a tosyloxy group at the α-carbon of an enolisable ketone. The resulting α-tosyloxy ketone reacts with nucleophiles at the α-carbon in the same way as an α-halo ketone, and in most cases it is used in the next step without isolation.[11]
In a one-pot example, acetophenone is heated under reflux in acetonitrile with 1.1 equivalents of Koser’s reagent for 2 hours. Sodium azide is then added at room temperature, and 2-azido-1-phenylethanone is isolated in 80% yield (Figure 4a).[12] Six other ketones gave the α-azido ketones in 69–81% yield by the same sequence, including 81% for cyclohexanone.[12]
The α-tosyloxy ketones can replace α-halo ketones in the Hantzsch thiazole synthesis. With thioureas they give 2-aminothiazoles and 2-(arylamino)thiazoles in one pot (Figure 4b),[13] and a review also lists thioamides as substrates for this modified Hantzsch synthesis.[11] With ethylenethiourea, acetophenones give 3-aryl-5,6-dihydroimidazo[2,1-b]thiazoles, also without isolation of the tosylate (Figure 4c).[14]
α-Tosyloxy ketones are also precursors of oxyallyl cations for [4+3] cycloadditions. 2-Tosyloxycyclohexanone, prepared from cyclohexanone and Koser’s reagent, reacts with furan in trifluoroethanol in the presence of triethylamine to give the bridged cycloadduct (Figure 4d).[15] The yields are similar to those obtained with α-halo and α-mesyloxy ketones, but the tosyloxy ketones are easier to prepare and more stable, and they generally do not require chromatography.[15]
Figure 4. α-Functionalisation of ketones with Koser’s reagent. (a) Acetophenone to 2-azido-1-phenylethanone in one pot.[12] (b) Aryl methyl ketones to 2-aminothiazoles with thiourea.[13] (c) Acetophenones to 3-aryl-5,6-dihydroimidazo[2,1-b]thiazoles with ethylenethiourea.[14] (d) Cyclohexanone to the [4+3] cycloadduct with furan.[15] The yield in (a) is that of a single example; (b) to (d) show the general transformation.
Two related methods use other substrates. Koser’s reagent converts aromatic, aliphatic and cyclic enol esters rapidly into α-tosyloxy ketones,[16] and it promotes the oxidative transposition of vinyl halides to α-halo ketones.[17]
PIDA in methanolic KOH: α-hydroxy dimethyl acetals
Under basic conditions in methanol, PIDA oxidises ketones to α-hydroxy dimethyl acetals (Figure 5a).[18] α,β-Unsaturated ketones that cannot enolise, or that have one β-substituent, give α-hydroxy-β-methoxy dimethyl acetals (Figure 5b), whereas enolisable β,β-disubstituted enones give α′-hydroxy enones.[19]
Chromones, flavones, chalcones and flavanones also give α-hydroxy-β-methoxy dimethyl acetals, and hydrolysis of the acetals gives 3-hydroxychromones and 3-hydroxyflavones.[11]
The 1,2-aryl shift
Iodine(III) reagents also promote 1,2-aryl shifts. Alkyl aryl ketones rearrange to 2-arylalkanoates.[18] With Koser’s reagent in acetonitrile, flavanones undergo a 1,2-aryl shift to give isoflavones, whereas in methanol the same reagent gives flavones (Figure 5c).[11]
1,3-Dicarbonyl compounds
PIDA also functionalises the α-carbon of 1,3-dicarbonyl compounds. With tetrabutylammonium azide the α-azido compounds are obtained,[20] and with chlorotrimethylsilane or bromotrimethylsilane the α-monochloro or α-monobromo compounds (Figure 5d).[21]
Figure 5. PIDA in methanolic KOH, the 1,2-aryl shift and 1,3-dicarbonyl compounds. (a) Ketones to α-hydroxy dimethyl acetals.[18] (b) Enones to α-hydroxy-β-methoxy dimethyl acetals.[19] (c) Flavanone to isoflavone or flavone with Koser’s reagent, depending on the solvent.[11] (d) 1,3-Dicarbonyl compounds to the α-azido and α-chloro compounds.[20][21] All panels show the general transformation.
Practical points
| Point | What the sources report |
|---|---|
| Koser’s reagent | 1.1 equivalents in acetonitrile at reflux for 2 hours, for acetophenone.[12] Dichloromethane is used for some substrates, such as benzalacetones.[11] |
| The α-tosyloxy ketone | Usually used without isolation.[11][12] When it is isolated, chromatography is generally unnecessary.[15] |
| Sonication | Used in the preparation of the α-tosyloxy ketones for the [4+3] reaction; in an ultrasonic cleaning bath the yield depended on the position of the flask.[15] |
| PIDA under basic conditions | KOH in methanol.[18][19] |
| Solvent and product | Flavanones with Koser’s reagent: acetonitrile gives isoflavones, methanol gives flavones.[11] |
Koser’s reagent converts a ketone into an α-tosyloxy ketone, which reacts in one pot like an α-halo ketone to give α-azido ketones, thiazoles, fused imidazothiazoles and [4+3] cycloadducts. PIDA in methanolic KOH gives α-hydroxy dimethyl acetals.
Products: Koser’s reagent · PIDA
References (section 2)
- Sushma, R. Pundeer. Expanding the role of organoiodine(III) reagents as a versatile tool for various synthetic transformations. Arkivoc 2026, (2), 202612590. doi:10.24820/ark.5550190.p012.590 (open access)
- O. Prakash, K. Pannu, R. Prakash, A. Batra. [Hydroxy(tosyloxy)iodo]benzene mediated α-azidation of ketones. Molecules 2006, 11, 523–527. doi:10.3390/11070523 (open access)
- R. M. Moriarty, B. K. Vaid, M. P. Duncan, S. G. Levy, O. Prakash, S. Goyal. A one-pot synthesis of 2-amino- and 2-(arylamino)-substituted thiazoles and selenazoles using [hydroxy(tosyloxy)iodo]benzene, carbonyl compounds, and thioureas or selenoureas: a modification of the Hantzsch synthesis. Synthesis 1992, 845–846. doi:10.1055/s-1992-26243
- O. Prakash, N. Rani, S. Goyal. Hypervalent iodine in the synthesis of bridgehead heterocycles: novel and facile syntheses of 3-substituted-5,6-dihydroimidazo[2,1-b]thiazoles and 3-phenylthiazolo[3,2-a]benzimidazole from acetophenones using [hydroxy(tosyloxy)iodo]benzene. J. Chem. Soc., Perkin Trans. 1 1992, 707–709. doi:10.1039/P19920000707
- S. T. Handy, M. Okello. α-Tosyloxyketones: convenient [4+3] cycloaddition precursors. Synlett 2002, 489–491. doi:10.1055/s-2002-20474
- B. Basdevant, C. Y. Legault. Study of the reactivity of [hydroxy(tosyloxy)iodo]benzene toward enol esters to access α-tosyloxy ketones. J. Org. Chem. 2015, 80, 6897–6902. doi:10.1021/acs.joc.5b00948
- A. Jobin-Des Lauriers, C. Y. Legault. Iodine(III)-mediated oxidative hydrolysis of haloalkenes: access to α-halo ketones by a release-and-catch mechanism. Org. Lett. 2016, 18, 108–111. doi:10.1021/acs.orglett.5b03345
- R. M. Moriarty, O. Prakash. Oxidation of carbonyl compounds with organohypervalent iodine reagents. Org. React. 1999, 54, 273–418.
- Y. Tamura, T. Yakura, H. Terashi, J. Haruta, Y. Kita. Hypervalent iodine oxidation of α,β-unsaturated carbonyl compounds. Chem. Pharm. Bull. 1987, 35, 570–577. doi:10.1248/cpb.35.570
- M. J. Galligan, R. Akula, H. Ibrahim. Unified strategy for iodine(III)-mediated halogenation and azidation of 1,3-dicarbonyl compounds. Org. Lett. 2014, 16, 600–603. doi:10.1021/ol403504z
- S. Chong, Y. Su, L. Wu, W. Zhang, J. Ma, X. Chen, D. Huang, K.-H. Wang, Y. Hu. Trimethylchlorosilane-mediated mild α-chlorination of 1,3-dicarbonyl compounds promoted by phenyliodonium diacetate. Synthesis 2016, 48, 1359–1370. doi:10.1055/s-0035-1561572
3. Phenols: oxidative dearomatisation with PIDA or PIFA
PIDA and PIFA oxidise phenols to cyclohexadienones. The ring is dearomatised, and a nucleophile adds at the carbon para or ortho to the oxygen. In methanol, for example, PIDA converts phenols into p‑quinones, o‑quinones, 4,4‑dialkoxycyclohexa-2,5‑dienones or 4‑alkyl-4-alkoxycyclohexa-2,5‑dienones, depending on the substituents of the phenol.[22]
The nucleophile is the solvent or a group in the same molecule, and it determines the product: methanol gives ketals, water gives p‑quinols, and a carboxylic acid in a side chain gives a spirolactone.
Mechanism
The phenol first displaces one acetate or trifluoroacetate ligand on iodine to give an aryloxy-iodane. This step is widely accepted, but the following step has been debated.[23]
In one proposal, the nucleophile attacks the iodine-bound phenol directly. In the other, iodobenzene is lost first to give a phenoxenium ion (a cation with the positive charge delocalised over the ring), and the nucleophile then adds to this cation.[23] A study of substituent effects with 4‑arylphenols supports the phenoxenium ion,[23] in agreement with earlier calculations on the site of attack in substituted phenols.[24]
Para-dearomatisation: quinone monoketals, p‑quinols and p‑quinones
In methanol, a 4‑alkoxyphenol is attacked at the alkoxy-substituted carbon, and the product is a p‑quinone monoketal.[22][25] With 1.1 equivalents of PIDA in methanol (0 °C, then room temperature for 3 hours), 4‑methoxyphenol gave 4,4‑dimethoxycyclohexa-2,5‑dienone in 99% yield (Figure 6a).[23] 4‑Alkylphenols similarly give 4‑alkyl-4-methoxycyclohexa-2,5‑dienones (Figure 6b).[22]
With water as the nucleophile, the product is a p‑quinol (a 4‑hydroxycyclohexa-2,5‑dienone). PIFA in aqueous acetonitrile at 0 °C converts para-substituted phenols into p‑quinols in moderate to good yields, and the yields are higher when the tripropylsilyl ethers of the phenols are used as substrates (Figure 6b).[26]
The same effect was observed with PIDA and the trimethylsilyl ethers of 4‑arylphenols: the silyl ethers gave the p‑arylquinols in higher yield than the free phenols, because fewer oligomers were formed.[27]
p‑Quinones can also be obtained: PIFA converts p‑alkoxyphenols and related phenols into p‑quinones in excellent yields under mild conditions.[28]
Figure 6. Para-dearomatisation. (a) 4‑Methoxyphenol to 4,4‑dimethoxycyclohexa-2,5‑dienone with PIDA in methanol.[23] (b) A 4‑alkylphenol (R = alkyl) gives the 4‑methoxy dienone with PIDA in methanol[22] and the p‑quinol with PIFA in aqueous acetonitrile.[26] The yield in (a) is that of a single example; (b) shows the general transformation.
Spirocyclisation with an intramolecular nucleophile
When the nucleophile is in a side chain, the addition forms a ring, and the product is a spirocyclic dienone.[29] A 3-(4‑hydroxyphenyl)propanoic acid gives a spirolactone in this way.[25]
In one example, the 2‑methoxy derivative gave the spirolactone in 46% yield with 1.04 equivalents of PIFA in acetone at 0 °C. With lead tetraacetate in acetone at room temperature, the same spirolactone was obtained in only 10% yield (Figure 7a).[30]
N‑Protected tyrosines also give spirolactones with PIDA, and phenols with an amide in the side chain give spirolactams. The spirolactam examples in the review include reactions in hexafluoro-2-propanol (HFIP) and in 2,2,2‑trifluoroethanol (TFE), and the review also describes the use of these spirocyclisations in natural product synthesis.[29]
Ortho-dearomatisation: masked o‑benzoquinones
In a 2‑methoxyphenol, the methoxy group directs the attack of methanol to the methoxy-substituted carbon. The product is a 6,6‑dimethoxycyclohexa-2,4‑dienone, an ortho-quinone monoketal, also called a masked o‑benzoquinone.[31][32] These compounds are most conveniently prepared with PIDA in methanol.[31]
Masked o‑benzoquinones are reactive dienes, and in the absence of a dienophile they dimerise by a Diels–Alder reaction.[31][32] When a 2‑methoxyphenol with a nitrovinyl group was oxidised without a dienophile, the dimer was obtained in 94% yield within 10 minutes.[32]
The dimerisation is avoided when the dienophile is present before PIDA is added. With 10 equivalents of ethyl vinyl ether, the same phenol gave the bicyclo[2.2.2]octenone in 95% yield after 10 minutes at room temperature (Figure 7b).[32]
Substituents also slow the dimerisation: a bromine atom at C‑4, or a small alkyl or alkoxy group at C‑5, has this effect, and the 4‑bromo monoketal is stable enough to be isolated (Figure 7c).[31]
Figure 7. Spirocyclisation and ortho-dearomatisation. (a) A phenolic propanoic acid to the spirolactone with PIFA.[30] (b) A 2‑methoxyphenol to the masked o‑benzoquinone, which is trapped in situ by ethyl vinyl ether; PIDA is added to the phenol and ethyl vinyl ether in methanol.[32] (c) 4‑Bromo-2-methoxyphenol gives a masked o‑benzoquinone that can be isolated; the yield range is the one quoted in reference [31]. The yields in (a) and (b) are those of single examples.
Practical points
| Point | What the sources report |
|---|---|
| Amount of reagent | 1.04–1.2 equivalents in the examples with stated amounts.[23][30][32] |
| Temperature and time | 0 °C to room temperature; 10 minutes to 3 hours.[23][30][32] |
| Solvent | Methanol for ketals;[22][23][31] aqueous acetonitrile for p‑quinols;[26] acetone for the spirolactone of Figure 7a.[30] HFIP and TFE are used in spirolactam examples.[29] |
| Work-up | For the ketal of Figure 6a: 10% aqueous sodium thiosulfate, extraction with ethyl acetate, then chromatography.[23] |
| Free phenol or silyl ether | For p‑quinols, the silyl ethers gave higher yields than the free phenols.[26][27] |
| 2‑Methylphenols | In methanol, 2‑methyl-5-tert-butylphenol reacted with a loss of regioselectivity; the authors attribute it to the harder nucleophilic character of methanol compared with acetic acid and to the similar electrophilic reactivity of C‑2 and C‑4.[31] |
| Masked o‑benzoquinones | The dienophile is added before PIDA; without it, the dimer formed within 10 minutes.[32] |
| PIDA or PIFA | In the examples above, PIDA was used for the ketals and the masked o‑benzoquinones, and PIFA for the p‑quinols, the p‑quinones and the spirolactone. The sources read here do not compare the two reagents on the same phenol. |
The nucleophile determines the product: methanol gives quinone monoketals, water gives p‑quinols, and a carboxylic acid in a side chain gives a spirolactone. Masked o‑benzoquinones from 2‑methoxyphenols dimerise within minutes, so the dienophile must be present before PIDA is added.
References (section 3)
- A. Pelter, S. M. A. Elgendy. Phenolic oxidations with phenyliodonium diacetate. J. Chem. Soc., Perkin Trans. 1 1993, 1891–1896. doi:10.1039/P19930001891
- T. Tang, A. M. Harned. Experimental evidence for the formation of cationic intermediates during iodine(III)-mediated oxidative dearomatization of phenols. Org. Biomol. Chem. 2018, 16, 8249–8252. doi:10.1039/C8OB01652F
- L. Kürti, P. Herczegh, J. Visy, M. Simonyi, S. Antus, A. Pelter. New insights into the mechanism of phenolic oxidation with phenyliodonium(III) reagents. J. Chem. Soc., Perkin Trans. 1 1999, 379–380. doi:10.1039/A809206K
- Y. Tamura, T. Yakura, J. Haruta, Y. Kita. Hypervalent iodine oxidation of p‑alkoxyphenols and related compounds: a general route to p‑benzoquinone monoacetals and spiro lactones. J. Org. Chem. 1987, 52, 3927–3930. doi:10.1021/jo00226a041
- A. McKillop, L. McLaren, R. J. K. Taylor. A simple and efficient procedure for the preparation of p‑quinols by hypervalent iodine oxidation of phenols and phenol tripropylsilyl ethers. J. Chem. Soc., Perkin Trans. 1 1994, 2047–2048. doi:10.1039/P19940002047
- F.-X. Felpin. Oxidation of 4‑arylphenol trimethylsilyl ethers to p‑arylquinols using hypervalent iodine(III) reagents. Tetrahedron Lett. 2007, 48, 409–412. doi:10.1016/j.tetlet.2006.11.073
- Y. Tamura, T. Yakura, H. Tohma, K. Kikuchi, Y. Kita. Hypervalent iodine oxidation of p‑alkoxy- and related phenols: a facile and efficient synthesis of p‑quinones. Synthesis 1989, 126–127. doi:10.1055/s-1989-27170
- F. V. Singh, P. B. Kole, S. R. Mangaonkar, S. E. Shetgaonkar. Synthesis of spirocyclic scaffolds using hypervalent iodine reagents. Beilstein J. Org. Chem. 2018, 14, 1778–1805. doi:10.3762/bjoc.14.152 (open access)
- G. L. Plourde, B. B. Fisher. Synthesis of 6‑methoxy-1-oxaspiro[4,5]deca-6,9‑diene-8-one. Molecules 2002, 7, 315–319. doi:10.3390/70200315 (open access)
- S. Quideau, L. Pouységu, D. Deffieux, A. Ozanne, J. Gagnepain, I. Fabre, M. Oxoby. Iodane-mediated and electrochemical oxidative transformations of 2‑methoxy- and 2‑methylphenols. Arkivoc 2003, (vi), 106–119. doi:10.3998/ark.5550190.0004.613 (open access)
- S. Sharma, R. T. Naganaboina, R. K. Peddinti. Expedient synthesis of nitrovinyl substituted bicyclo[2.2.2]octenone scaffolds. RSC Adv. 2015, 5, 100060–100069. doi:10.1039/C5RA20016D
4. Electron-rich arenes with PIFA: radical cations, azidation and biaryl coupling
PIFA also oxidises arenes without a hydroxy group, such as anisoles and other phenol ethers. Phenols react with iodine(III) through the hydroxy group (section 3). Phenol ethers instead transfer one electron to PIFA and form an arene radical cation.[33]
The radical cation was detected by UV and ESR spectroscopy. It is formed by single-electron transfer within a charge-transfer complex of the arene and PIFA.[33]
Nucleophilic substitution via the radical cation
These reactions proceed well in hexafluoro-2-propanol, (CF3)2CHOH (HFIP), a polar solvent of low nucleophilicity.[33] A later study attributes this solvent effect to the stabilisation of the cationic intermediates and reports lower yields of the substitution products in dichloromethane.[34]
A nucleophile then attacks the radical cation. With p‑substituted anisoles, PIFA in HFIP followed by trimethylsilyl azide gives aryl azides with the azido group ortho to the methoxy group (Figure 8, top), in 31–82% yield for the series.[33][35] Thiols, acetate and β-dicarbonyl compounds also react as nucleophiles.[33]
The authors attribute the site of attack to the spin density of the radical cation, which is located mainly ortho to the methoxy group according to the ESR spectrum and Hückel calculations.[33]
In acetonitrile, the same reagents give a different product: p‑alkylanisoles with benzylic hydrogen atoms are azidated at the benzylic carbon (Figure 8, bottom; 24–79% yield for the series). In this case the reactive intermediate is a benzylic radical.[33][36]
Koser’s reagent also generates arene radical cations in HFIP: with 1,4‑dimethoxybenzene, the radical cation was observed by UV–visible and ESR spectroscopy.[34] Unsubstituted and meta-substituted phenol ethers react differently and give diaryliodonium salts (section 11).[33]
Figure 8. The solvent determines the site of azidation. In HFIP, PIFA followed by trimethylsilyl azide gives azidation of the ring, ortho to the methoxy group;[33][35] in acetonitrile, PIFA and trimethylsilyl azide give azidation at the benzylic carbon.[33][36] General transformations; the yields of the two series were 31–82% and 24–79%.[33]
Metal-free biaryl coupling
With BF3·Et2O in dichloromethane, PIFA couples electron-rich arenes to give biaryls. The coupling can be intramolecular, as in 1,3‑diarylpropanes and N‑benzyl-N-phenethylamines,[37] or intermolecular, which gives substituted biphenyls and binaphthyls in high yields.[38] Alkylarenes couple analogously,[39] and alkylthiophenes give 2,2′-bithiophenes.[40]
In one intramolecular example, a 3,4‑bis(3,4‑dimethoxyphenyl)pyrrolinone gave the tetramethoxy-dibenzoisoindolone in 96% yield with 1.1 equivalents of PIFA and 1.2 equivalents of BF3·Et2O in dichloromethane at −40 °C (Figure 9a).[41] The cyclisation required at least two methoxy groups, with at least one of them para to the new bond; the bis(3‑methoxyphenyl) analogue gave 45%.[41]
The same study compared other conditions (Table 2). Without BF3·Et2O, PIFA gave the product in 75% yield; DDQ and m-CPBA, each with trifluoroacetic acid, gave 22% and 38%; BF3·Et2O alone gave no product.[41] The study also cites an earlier cyclisation in which BF3·Et2O increased the yield from 25% to 91%.[41]
| Oxidant | Additive | Temperature, time | Product : starting material | Yield |
|---|---|---|---|---|
| PIFA | BF3·Et2O | −40 °C, 4 h | 100 : 0 | 96% |
| PIFA | BF3·Et2O | +4 °C, 12 h | 100 : 0 | 90% |
| PIFA | none | −40 °C, 4 h | 90 : 10 | 75% |
| m-CPBA | TFA | rt, 4 h | 80 : 20 | 38% |
| DDQ | TFA | rt, 4 h | 50 : 50 | 22% |
| none | BF3·Et2O | −40 °C, 4 h | 0 : 100 | 0% |
Table 2. Conditions compared for the cyclisation of Figure 9a. The results are those of the bis(3,4‑dimethoxyphenyl) compound, as in the text and the experimental section of the source. The ratio of product to starting material was measured by 1H NMR; the yields are isolated yields.[41]
Cross-coupling of two different arenes is also possible. Naphthalenes and other electron-rich arenes couple with mesitylene in high yields;[42] with 3 equivalents of mesitylene, phenanthrene gave 9‑mesitylphenanthrene in 78% yield (Figure 9b).[42]
Iodine substituents are tolerated: iodinated arenes give iodinated biaryls in up to 75% yield with PIFA.[43]
PIDA can also be used with very electron-rich arenes. In the dimerisation of 1,2,4‑trimethoxynaphthalene, PIFA and PIDA, each with BF3·OEt2, gave the dimer in 63% and 59% yield. The authors considered these results better overall than those of the other oxidants tested, which included cerium(IV) ammonium nitrate and iron(III) chloride.[44]
Figure 9. Biaryl coupling with PIFA and BF3·Et2O. (a) Intramolecular coupling to a dibenzoisoindolone.[41] (b) Cross-coupling of phenanthrene with mesitylene, under the conditions of the typical procedure in the source.[42] The yields are those of single examples.
Practical points
| Point | What the sources report |
|---|---|
| Solvent for substitution | HFIP;[33] in dichloromethane the yields were lower.[34] In acetonitrile, p‑alkylanisoles are azidated at the benzylic carbon instead.[33][36] |
| Order of addition, azidation in HFIP | PIFA in HFIP first, then trimethylsilyl azide.[35] |
| Lewis acid for biaryl coupling | BF3·Et2O: 1.2 equivalents for Figure 9a[41] and 2 equivalents in the cross-coupling procedure.[42] Without it, the yields were lower in the cases compared.[41] |
| Temperature | −40 °C for Figure 9a (at +4 °C for 12 hours the yield was still 90%);[41] −78 °C for 3 hours in the cross-coupling procedure.[42] |
| Cross-coupling | Order of addition: both arenes (mesitylene, 3 equivalents), then BF3·Et2O, then PIFA.[42] |
| Work-up, cross-coupling | Saturated aqueous sodium hydrogen carbonate, extraction with dichloromethane, then chromatography.[42] |
| Substitution pattern of the phenol ether | p‑Substituted phenol ethers undergo substitution via the radical cation; unsubstituted and meta-substituted ones give diaryliodonium salts.[33] |
PIFA oxidises electron-rich arenes to radical cations. In HFIP, a nucleophile such as azide adds to the ring ortho to a methoxy group; with BF3·Et2O at low temperature, two arenes are coupled to a biaryl without a metal catalyst.
Products: PIFA · Koser’s reagent
References (section 4)
- Y. Kita, T. Takada, H. Tohma. Hypervalent iodine reagents in organic synthesis: nucleophilic substitution of p‑substituted phenol ethers. Pure Appl. Chem. 1996, 68, 627–630. doi:10.1351/pac199668030627 (open access)
- M. Ito, C. Ogawa, N. Yamaoka, H. Fujioka, T. Dohi, Y. Kita. Enhanced reactivity of [hydroxy(tosyloxy)iodo]benzene in fluoroalcohol media. Efficient direct synthesis of thienyl(aryl)iodonium salts. Molecules 2010, 15, 1918–1931. doi:10.3390/molecules15031918 (open access)
- Y. Kita, H. Tohma, M. Inagaki, K. Hatanaka, T. Yakura. A novel oxidative azidation of aromatic compounds with hypervalent iodine reagent, phenyliodine(III) bis(trifluoroacetate) (PIFA) and trimethylsilyl azide. Tetrahedron Lett. 1991, 32, 4321–4324. doi:10.1016/S0040-4039(00)92160-9
- Y. Kita, H. Tohma, T. Takada, S. Mitoh, S. Fujita, M. Gyoten. A novel and direct alkyl azidation of p‑alkylanisoles using phenyl iodine(III) bis(trifluoroacetate) (PIFA) and trimethylsilyl azide. Synlett 1994, 427–428. doi:10.1055/s-1994-22875
- Y. Kita, M. Gyoten, M. Ohtsubo, H. Tohma, T. Takada. Non-phenolic oxidative coupling of phenol ether derivatives using phenyliodine(III) bis(trifluoroacetate). Chem. Commun. 1996, 1481–1482. doi:10.1039/CC9960001481
- H. Tohma, H. Morioka, S. Takizawa, M. Arisawa, Y. Kita. Efficient oxidative biaryl coupling reaction of phenol ether derivatives using hypervalent iodine(III) reagents. Tetrahedron 2001, 57, 345–352. doi:10.1016/S0040-4020(00)00941-8
- H. Tohma, M. Iwata, T. Maegawa, Y. Kita. Novel and efficient oxidative biaryl coupling reaction of alkylarenes using a hypervalent iodine(III) reagent. Tetrahedron Lett. 2002, 43, 9241–9244. doi:10.1016/S0040-4039(02)02150-0
- H. Tohma, M. Iwata, T. Maegawa, Y. Kiyono, A. Maruyama, Y. Kita. A novel and direct synthesis of alkylated 2,2′-bithiophene derivatives using a combination of hypervalent iodine(III) reagent and BF3·Et2O. Org. Biomol. Chem. 2003, 1, 1647–1649. doi:10.1039/B302462H
- A. A. van Loon, M. K. Holton, C. R. Downey, T. M. White, C. E. Rolph, S. R. Bruening, G. Li, K. M. Delaney, S. J. Pelkey, E. T. Pelkey. Preparation of dibenzo[e,g]isoindol-1-ones via Scholl-type oxidative cyclization reactions. J. Org. Chem. 2014, 79, 8049–8058. doi:10.1021/jo501185f (open access)
- T. Dohi, M. Ito, K. Morimoto, M. Iwata, Y. Kita. Oxidative cross-coupling of arenes induced by single-electron transfer leading to biaryls by use of organoiodine(III) oxidants. Angew. Chem. Int. Ed. 2008, 47, 1301–1304. doi:10.1002/anie.200704495
- D. Mirk, A. Willner, R. Fröhlich, S. R. Waldvogel. Iodinated biaryls synthesized by the direct dehydrodimerization of iodoarenes using phenyliodine(III) bis(trifluoroacetate) (PIFA). Adv. Synth. Catal. 2004, 346, 675–681. doi:10.1002/adsc.200404024
- S.-k. Daley, N. Downer-Riley. The biomimetic synthesis of balsaminone A and ellagic acid via oxidative dimerization. Beilstein J. Org. Chem. 2020, 16, 2026–2031. doi:10.3762/bjoc.16.169 (open access)
5. Primary amides to amines: the Hofmann rearrangement
PIFA, PIDA and Koser’s reagent convert primary amides into amines with one carbon atom fewer. The amide nitrogen is oxidised, the alkyl or aryl group migrates from the carbonyl carbon to nitrogen, and an isocyanate is formed. The migrating group retains its configuration.[45]
The isocyanate then reacts with the nucleophile present (Figure 10b): water gives the amine,[45] methanol gives a methyl carbamate[46] and ammonia gives a urea.[47]
PIFA: the amine under mildly acidic conditions
With PIFA in aqueous acetonitrile, the reaction proceeds under mildly acidic conditions. The trifluoroacetic acid released catalyses the hydrolysis of the isocyanate and protonates the amine, so the amine cannot react with the isocyanate to give a urea.[45]
In the Organic Syntheses procedure, 25 mmol of cyclobutanecarboxamide is stirred with 1.5 equivalents of PIFA in acetonitrile–water (1:1) for 4 hours, and cyclobutylamine is isolated as the hydrochloride in 69–77% yield (Figure 10a).[45]
Addition of pyridine to about pH 3.5 accelerates the reaction, whereas added acid or trifluoroacetate slows it. An alkene in the substrate can be tolerated: 3‑cyclohexene-1-carboxamide rearranges with one equivalent of PIFA, because the amide reacts faster than the alkene.[45]
Asparagine to 2,3‑diaminopropionic acid
The same reaction converts the side-chain amide of asparagine into an amine to give 2,3‑diaminopropionic acid (Dap); glutamine analogously gives 2,4‑diaminobutyric acid (Dab).[48]
In a synthesis of Fmoc-protected azido amino acids, Fmoc-Asn-OH gave Fmoc-Dap-OH in 80% yield with 1.5 equivalents of PIFA in DMF–water (2:1), with pyridine added after 15 minutes, at room temperature for 14 hours (Figure 10c). The product precipitated at pH 6 and was isolated by filtration, without chromatography, on a multigram scale. Fmoc-Gln-OH gave Fmoc-Dab-OH in 74% yield.[48]
In peptides, PIDA induces the selective rearrangement of the side-chain amide of asparagine in neutral water at 37 °C. The rearrangement gives a five-membered N‑acylurea, which is hydrolysed, so the peptide is cleaved at asparagine. Twenty oligopeptides with a protected N‑terminus were cleaved by this method, including one with a disulfide bond and one with D-amino acids.[49]
PIDA in methanol: carbamates and ureas
In methanolic KOH at 5–10 °C, PIDA converts primary amides into methyl carbamates. Fourteen alkyl and aryl carboxamides gave the carbamates in 72% (methyl N‑cyclopropylcarbamate) to 97% (methyl N‑phenylcarbamate) yield, and the products were purified by chromatography on silica gel.[46]
With ammonia or ammonium carbamate in methanol, PIDA gives primary ureas instead. The isocyanate is trapped by ammonia, and the methyl carbamate was not observed, although methanol was the solvent.[47]
Koser’s reagent: ammonium tosylates
Koser’s reagent converts aliphatic carboxamides directly into alkylammonium tosylates.[50]
Figure 10. The Hofmann rearrangement with iodine(III) reagents. (a) Cyclobutanecarboxamide to cyclobutylamine, isolated as the hydrochloride.[45] (b) The isocyanate gives the amine with water, the methyl carbamate with methanol and the urea with ammonia; the amine is obtained as its salt, the trifluoroacetate with PIFA and the tosylate with Koser’s reagent.[45][46][47][50] (c) Fmoc-Asn-OH to Fmoc-Dap-OH.[48] The yields in (a) and (c) are those of single examples; (b) shows the general transformations.
Practical points
| Point | What the sources report |
|---|---|
| Amount of PIFA | 1.5 equivalents in both procedures shown.[45][48] |
| Solvent | Acetonitrile–water (1:1);[45] DMF–water (2:1) for the Fmoc amino acids.[48] |
| pH | Pyridine to about pH 3.5 accelerates the reaction; added acid or trifluoroacetate slows it.[45] For Fmoc-Asn-OH, pyridine (2.1 equivalents) was added after 15 minutes.[48] |
| Reagent quality | A yellow reagent gave poor yields; in the procedure, PIFA is stored in a dark bottle under nitrogen or argon.[45] |
| Work-up, amine | With hydrochloric acid, the amine remains in the aqueous phase as the hydrochloride, and unreacted PIFA is extracted into the ether layer as iodobenzene dichloride.[45] |
| Work-up, Fmoc-Dap-OH | Precipitation at pH 6 and filtration; no chromatography.[48] |
| Methyl carbamates | PIDA, KOH, methanol, 5–10 °C; chromatography on silica gel.[46] |
| Ureas | PIDA with ammonia or ammonium carbamate in methanol.[47] |
The iodine(III) reagent converts a primary amide into an isocyanate, and the nucleophile present determines the product: water gives the amine, methanol the methyl carbamate and ammonia the urea. With PIFA, the acid released protonates the amine, so no urea by-product is formed.
Products: PIFA · PIDA · Koser’s reagent
References (section 5)
- M. R. Almond, J. B. Stimmel, E. A. Thompson, G. M. Loudon. Hofmann rearrangement under mildly acidic conditions using [I,I-bis(trifluoroacetoxy)]iodobenzene: cyclobutylamine hydrochloride from cyclobutanecarboxamide. Org. Synth. 1988, 66, 132. doi:10.15227/orgsyn.066.0132 (open access)
- R. M. Moriarty, C. J. Chany II, R. K. Vaid, O. Prakash, S. M. Tuladhar. Preparation of methyl carbamates from primary alkyl- and arylcarboxamides using hypervalent iodine. J. Org. Chem. 1993, 58, 2478–2482. doi:10.1021/jo00061a022
- N. Saraiva Rosa, T. Glachet, Q. Ibert, J.-F. Lohier, X. Franck, V. Reboul. A straightforward synthesis of N‑substituted ureas from primary amides. Synthesis 2020, 52, 2099–2105. doi:10.1055/s-0040-1707103
- Y. H. Lau, D. R. Spring. Efficient synthesis of Fmoc-protected azido amino acids. Synlett 2011, 1917–1919. doi:10.1055/s-0030-1260950
- K. Tanabe, A. Taniguchi, T. Matsumoto, K. Oisaki, Y. Sohma, M. Kanai. Asparagine-selective cleavage of peptide bonds through hypervalent iodine-mediated Hofmann rearrangement in neutral aqueous solution. Chem. Sci. 2014, 5, 2747–2753. doi:10.1039/C3SC53037J
- I. M. Lazbin, G. F. Koser. Direct conversion of aliphatic carboxamides to alkylammonium tosylates with [hydroxy(tosyloxy)iodo]benzene. J. Org. Chem. 1986, 51, 2669–2671. doi:10.1021/jo00364a010
6. Nitrogen transfer: sulfoximines, isoquinolines and C–H amination
PIDA transfers nitrogen as well as oxygen. With an ammonia source such as ammonium carbamate, it generates a short-lived electrophilic nitrogen species, which transfers an NH group to sulfur or inserts a nitrogen atom into a ring (Figure 11).[51][55]
With a dirhodium catalyst, PIDA converts carbamates and sulfamate esters into cyclic products by insertion of the nitrogen into a C–H bond of the same molecule (Figure 12).[57][58]
The reactive species
Mechanistic studies suggest that the iminoiodinane PhI=NH or the iodonitrene PhI=N+ is the species that transfers the nitrogen. The intermediate is short-lived: neither species was observed by NMR spectroscopy, but mass spectrometry in flow gave signals consistent with both.[51]
Ammonium carbamate is a convenient solid source of ammonia and replaces hazardous nitrogen sources such as hydrazoic acid and O-mesitylenesulfonylhydroxylamine (MSH).[52] Ammonium acetate and ammonia in methanol can also be used.[53] The reaction is fastest in methanol and is carried out at room temperature in an open flask.[51][52]
Sulfoxides to NH-sulfoximines
Sulfoximines are of growing interest in drug discovery.[51] With 3 equivalents of PIDA and 4 equivalents of ammonium carbamate in methanol at 25 °C, a sulfoxide is fully converted into the NH-sulfoximine within 30 minutes. On a 10 mmol scale, methyl p‑tolyl sulfoxide gave the NH-sulfoximine in 91% yield (Figure 11a).[51]
The reaction is stereospecific: an enantioenriched sulfoxide gives the sulfoximine with retention of configuration at sulfur.[51]
Most functional groups are tolerated. The authors tested this by adding other compounds to the reaction mixture:[51]
- With pyridine, pyrimidine, quinoline, imidazole, thiazole, benzoxazole or benzothiazole added, the sulfoximine was still obtained in high yield; only N‑benzylpyrrole and N‑methylindole reduced the yield to below 85%.
- With an alkene, an alkyne, an alkylamine, a phenol, an ester, an aldehyde or a nitrile added, the yield remained above 96%. Alkenes are not aziridinated.[52]
- Electron-rich heteroarenes are less well tolerated: added indole, furan and thiophene were poorly recovered, and aniline reduced the yield to 65%.[51][52]
The method has been carried out on a 30 kg scale for an intermediate of AstraZeneca’s AZD6738. A toluene–methanol mixture was used to allow an aqueous extractive work-up, and the product was isolated as the hydrochloride in 83% yield.[52]
Sulfides: NH and O transfer in one pot
A sulfide can be converted directly into the NH-sulfoximine, because PIDA transfers both the NH group and the oxygen atom in one pot.[53] Methyl p‑tolyl sulfide gave the NH-sulfoximine in 95% yield with 2.5 equivalents of PIDA and 4 equivalents of ammonium carbamate in methanol at 25 °C for 2 hours (Figure 11b). With ammonium acetate or ammonia in methanol, the yield was 98%.[53]
The evidence suggests that the NH group is transferred first and that PIDA then oxidises the resulting sulfilimine. Under the optimised conditions no sulfoxide was detected, and in a control experiment without the nitrogen source the sulfoxide was not oxidised to the sulfone.[53]
With 15N‑labelled ammonium acetate, the method gives 15N‑labelled sulfoximines.[53]
Sulfinamides to NH-sulfonimidamides
Tertiary sulfinamides react analogously to give NH-sulfonimidamides, the nitrogen analogues of sulfonamides. 1-(Phenylsulfinyl)piperidine gave the sulfonimidamide in 94% yield with 3 equivalents of PIDA and 4 of ammonium carbamate in methanol (0.5 M) at room temperature for 1 hour, and in 88% yield on a 4.0 g scale (Figure 11c).[54]
Across the series, yields ranged from 17% to 95%. A sulfinamide of 51% ee gave the sulfonimidamide with 48% ee, so the reaction appears to be stereospecific.[54]
Primary and secondary sulfinamides are a limitation of the method. The primary sulfinamide tested gave no sulfonimidamide: a sulfonimidate was obtained in 58% yield, together with the sulfonamide (15%). The secondary sulfinamide tested gave a mixture, with a sulfonimidate as the main product.[54]
The same reagent system has also been used to prepare sulfonimidates and sulfonamides from thiophenols, terminal diazirines from amino acids and hydrazinium salts from amines; a 2023 review summarises this work.[52]
Nitrogen atom insertion into rings
PIDA and ammonium carbamate can also insert a nitrogen atom into a five-membered carbocycle. Indenes give isoquinolines, and cyclopentadienes give pyridines.[55]
In the general procedure, ammonium carbamate (4.0 equivalents) and then PIDA (2.5 equivalents) are added to the indene in methanol at 0 °C, and after 20 minutes the mixture is allowed to warm to room temperature. 3‑Phenyl-1H-indene gave 1‑phenylisoquinoline in 63% yield, and 3‑methyl-1H-indene gave 1‑methylisoquinoline in 64% (Figure 11d).[55]
In this reaction PIDA gave a higher yield than PIFA: under the same small-scale conditions, the NMR yield of 1‑phenylisoquinoline was 93% with PIDA and 77% with PIFA.[55]
With 2 equivalents of PIDA some starting material remained, and with 3 or more equivalents oxidative by-products were formed, so 2.5 equivalents were used on the larger scale.[55]
With 15NH4Cl as the nitrogen source, the method gives 15N‑labelled isoquinolines.[55]
Indoles undergo a related reaction when the indole nitrogen is protected with a silyl group, which suppresses its nucleophilicity. With ammonium carbamate and a hypervalent iodine reagent, they undergo ring expansion to quinazolines or quinoxalines, depending on the substitution pattern, and the method was applied to several commercial drugs.[56]
Figure 11. Nitrogen transfer with PIDA and ammonium carbamate (H2NCO2NH4). (a) Sulfoxide to NH-sulfoximine.[51] (b) Sulfide to the same NH-sulfoximine in one pot, with transfer of the NH group and of the oxygen atom; the author version of the paper does not state whether the 95% is an isolated or an NMR yield.[53] (c) Sulfinamide to NH-sulfonimidamide.[54] (d) Indene to isoquinoline by insertion of a nitrogen atom; isolated yields on a 1 mmol scale.[55] All yields are those of single examples.
Rhodium-catalysed C–H amination
In the proposed mechanism, PIDA first oxidises the NH2 group of a carbamate or a sulfamate ester to an iminoiodinane. With a dirhodium catalyst such as rhodium(II) acetate, iodobenzene is then lost and the nitrogen is inserted into a C–H bond. Magnesium oxide is added to neutralise the acetic acid formed from PIDA.[58]
The preferred ring size determines which carbon is aminated (Figure 12):[58]
- Carbamates give five-membered oxazolidin-2-ones, which are precursors of 1,2‑amino alcohols.[58]
- Sulfamate esters give six-membered oxathiazinanes, which are precursors of 1,3‑difunctionalised amines.[58] They react with nucleophiles in a similar way to an activated azetidine.[59]
In the general procedure for carbamates, the carbamate in dichloromethane is stirred with magnesium oxide (2.3 equivalents), PIDA (1.4 equivalents) and the rhodium catalyst (5 mol%) at 40 °C for 12 hours. The mixture is then filtered through Celite and the product is purified by chromatography.[57]
Tertiary C–H bonds react preferentially. For sulfamates with Rh2(OAc)4, the order of reactivity is tertiary > α to an ether oxygen or a nitrogen, or benzylic > secondary ≫ primary, and yields are usually above 70% when a tertiary or benzylic C–H bond is available.[58]
Amination of a stereogenic tertiary C–H centre in an optically active substrate proceeds with retention of configuration.[58][59]
The method has the following limitations:
- Carbamates have the narrowest scope: secondary CH2 groups are difficult to aminate, and carbamates of secondary alcohols generally give ketones instead of oxazolidinones.[59]
- Alkenes react competitively: unsaturated carbamates and sulfamates tend to give aziridines.[58]
The catalyst Rh2(esp)2 performs better than other dirhodium carboxylates. With this catalyst, selected intramolecular sulfamate insertions require as little as 0.15 mol%.[58]
Figure 12. Rhodium-catalysed C–H amination with PIDA. The reacting C–H bond is drawn with its hydrogen atom; R1 and R2 are alkyl groups, so this C–H bond is tertiary. (a) A carbamate gives an oxazolidin-2-one (five-membered ring), under the conditions of the general procedure.[57] (b) A sulfamate ester gives a [1,2,3]-oxathiazinane 2,2‑dioxide (six-membered ring).[58] General schemes, so no yields are given.
Practical points
| Reaction | What the sources report |
|---|---|
| Sulfoxide to NH-sulfoximine | PIDA (3 equiv), ammonium carbamate (4 equiv), methanol, 25 °C, open flask; full conversion within 30 minutes.[51] |
| Sulfide to NH-sulfoximine | PIDA (2.5 equiv), ammonium carbamate (4 equiv), methanol, 25 °C, 2 hours.[53] |
| Sulfinamide to sulfonimidamide | PIDA (3 equiv), ammonium carbamate (4 equiv), methanol (0.5 M), room temperature, open flask, 0.5–2 hours.[54] |
| Indene to isoquinoline | Ammonium carbamate (4.0 equiv), then PIDA (2.5 equiv), methanol, 0 °C, then room temperature. Work-up: evaporation, then dichloromethane and a wash with 1 M NaOH.[55] |
| Scale and flow | A 30 kg batch was run in toluene–methanol. In flow, ammonium acetate or aqueous ammonia replaces ammonium carbamate, which can precipitate and block the reactor.[52] |
| Carbamate to oxazolidinone | PIDA (1.4 equiv), MgO (2.3 equiv), Rh2(OAc)4 (5 mol%), dichloromethane, 40 °C, 12 hours; filtration through Celite.[57] |
With ammonium carbamate, PIDA is a source of electrophilic nitrogen: it converts sulfoxides, sulfides and sulfinamides into NH-sulfoximines and NH-sulfonimidamides, and it inserts a nitrogen atom into indenes. With a dirhodium catalyst, it converts carbamates and sulfamate esters into cyclic precursors of 1,2‑amino alcohols and 1,3‑difunctionalised amines by C–H amination.
Products: PIDA · PIFA · Rhodium(II) acetate
References (section 6)
- M. Zenzola, R. Doran, L. Degennaro, R. Luisi, J. A. Bull. Transfer of electrophilic NH using convenient sources of ammonia: direct synthesis of NH sulfoximines from sulfoxides. Angew. Chem. Int. Ed. 2016, 55, 7203–7207. doi:10.1002/anie.201602320 (open access)
- R. Luisi, J. A. Bull. Synthesis of sulfoximines and sulfonimidamides using hypervalent iodine mediated NH transfer. Molecules 2023, 28, 1120. doi:10.3390/molecules28031120 (open access)
- A. Tota, M. Zenzola, S. J. Chawner, S. St John-Campbell, C. Carlucci, G. Romanazzi, L. Degennaro, J. A. Bull, R. Luisi. Synthesis of NH-sulfoximines from sulfides by chemoselective one-pot N- and O-transfers. Chem. Commun. 2017, 53, 348–351. doi:10.1039/C6CC08891K
- F. Izzo, M. Schäfer, R. Stockman, U. Lücking. A new, practical one-pot synthesis of unprotected sulfonimidamides by transfer of electrophilic NH to sulfinamides. Chem. Eur. J. 2017, 23, 15189–15193. doi:10.1002/chem.201703272 (open access)
- P. Finkelstein, J. C. Reisenbauer, B. B. Botlik, O. Green, A. Florin, B. Morandi. Nitrogen atom insertion into indenes to access isoquinolines. Chem. Sci. 2023, 14, 2954–2959. doi:10.1039/D2SC06952K (open access)
- J. C. Reisenbauer, O. Green, A. Franchino, P. Finkelstein, B. Morandi. Late-stage diversification of indole skeletons through nitrogen atom insertion. Science 2022, 377, 1104–1109. doi:10.1126/science.add1383
- C. G. Espino, J. Du Bois. A Rh-catalyzed C–H insertion reaction for the oxidative conversion of carbamates to oxazolidinones. Angew. Chem. Int. Ed. 2001, 40, 598–600. doi:10.1002/1521-3773(20010202)40:3<598::AID-ANIE598>3.0.CO;2-9
- J. L. Roizen, M. E. Harvey, J. Du Bois. Metal-catalyzed nitrogen-atom transfer methods for the oxidation of aliphatic C–H bonds. Acc. Chem. Res. 2012, 45, 911–922. doi:10.1021/ar200318q
- J. Du Bois. Rhodium-catalyzed C–H amination. An enabling method for chemical synthesis. Org. Process Res. Dev. 2011, 15, 758–762. doi:10.1021/op200046v
7. Heterocycles by oxidative cyclisation
Many heterocycles are prepared by forming a bond between two atoms of the same molecule. PIDA and PIFA mediate such oxidative cyclisations without a metal, in most of the examples below at or below room temperature: the substrate loses two hydrogen atoms, and the iodine(III) reagent is reduced to iodobenzene. A 2016 review surveys these reactions by reagent.[60]
This section describes cyclisations that form a C–O, a C–N or a C–S bond (Figure 13) and two reactions in which a reactive intermediate generated by the reagent adds to an alkene (Figure 14).
N‑Acylhydrazones to 1,3,4‑oxadiazoles: a C–O bond
With PIDA in dichloromethane, the N‑acylhydrazone of an aldehyde cyclises to a 2,5‑disubstituted 1,3,4‑oxadiazole by attack of the carbonyl oxygen on the former aldehyde carbon (Figure 13a). A series of ten heterocyclyl oxadiazoles was obtained in 60–78% yield.[61]
The rate of cyclisation depends on the substrate. With a pyrazolyl substituent, the reaction was complete within 10 minutes at room temperature with 1 equivalent of PIDA, whereas the benzothiazolyl compounds required 2 equivalents and 30 minutes at reflux.[61]
PIFA also converts symmetrical and unsymmetrical aldazines, R–CH=N–N=CH–R′, into 2,5‑disubstituted 1,3,4‑oxadiazoles.[62]
Pyridylhydrazones to triazolopyridines: a C–N bond
Aldehyde hydrazones of 2‑hydrazinopyridine cyclise to [1,2,4]triazolo[4,3‑a]pyridines by formation of a bond between the hydrazone carbon and the pyridine nitrogen. With 1.1 equivalents of PIDA, added in portions to the hydrazone in dichloromethane, and stirring overnight at room temperature, seven 3-(pyrazol-4-yl) derivatives were obtained in 82–90% yield (Figure 13b).[63]
For the work-up, the solvent is evaporated, the residue is dissolved in warm ethanol, and the solid that forms on cooling is collected by filtration.[63]
Thiobenzanilides to benzothiazoles: a C–S bond
PIFA in 2,2,2‑trifluoroethanol converts thiobenzanilides into 2‑arylbenzothiazoles at room temperature within 30 minutes, in moderate yields (Figure 13c). The authors propose an aryl radical cation as the intermediate, the same type of intermediate as in the arene couplings of section 4.[64]
Figure 13. Oxidative cyclisations. (a) An aldehyde N‑acylhydrazone gives a 1,3,4‑oxadiazole (C–O bond); general scheme, with the yield range of one series of ten examples.[61] (b) A pyridylhydrazone gives a [1,2,4]triazolo[4,3‑a]pyridine (C–N bond); single example.[63] (c) A thiobenzanilide gives a 2‑arylbenzothiazole (C–S bond); general scheme, for which moderate yields are reported.[64]
N‑Methoxy amides: nitrenium ions that add to alkenes
PIFA converts an N‑methoxy amide (an O-alkyl hydroxamate) into an electrophilic nitrogen species, a nitrenium ion stabilised by the oxygen atom.[65]
When the molecule also contains an alkene, the authors propose that the nitrogen adds to it to form a bicyclic aziridinium ion. The ion pair with trifluoroacetate then collapses to the anti-addition product, a trifluoroacetate ester, and ammonia in methanol converts this ester into the hydroxy lactam (Figure 14a).[65]
Under the reported conditions, the hydroxamate reacts with PIFA (1.2 equivalents) in dichloromethane at 0 °C, and 1 equivalent of trifluoroacetic acid accelerates the reaction significantly. Five- to eight-membered lactams were prepared by this method, in most cases stereospecifically.[65]
The regioselectivity of the ring opening depends on the alkene. With a 1,2‑disubstituted alkene, the aziridinium ion is opened only at the less hindered position to give an α-hydroxyalkyl lactam; with 1,1‑disubstituted alkenes it is opened at the other carbon.[65] With an aromatic ring in place of the alkene, the same type of intermediate gives azaspirocyclic lactams.[65]
Oximes to isoxazolines: nitrile oxides from PIDA
PIDA in methanol with a catalytic amount of trifluoroacetic acid oxidises aldoximes to nitrile oxides. The nitrile oxides are trapped in situ by an alkene, either intramolecularly or intermolecularly, to give 2‑isoxazolines.[66]
PIDA also dearomatises phenols (section 3), so dearomatisation and intramolecular nitrile oxide cycloaddition can be carried out in one pot to give tricyclic isoxazolines from phenols.[66]
Trifluoroacetaldoxime requires different conditions. With triethylamine in methanol a complex mixture was formed, which the authors attribute to addition of methanol to the very electrophilic trifluoroacetonitrile oxide. Of the conditions tested, PIDA in dichloromethane gave the best yield.[67]
With 2 equivalents each of the oxime and PIDA, allylbenzene gave the 3‑trifluoromethyl-2-isoxazoline in 76% yield (Figure 14b), and other alkenes gave the isoxazolines in 20–91% yield; one electron-poor alkene gave only traces. Phenylacetylene and trimethylsilylacetylene gave the isoxazoles in 53% and 50% yield.[67]
Figure 14. Additions to alkenes. (a) An unsaturated N‑methoxy amide gives a hydroxy lactam through a nitrenium ion; general scheme for a 1,2‑disubstituted alkene.[65] (b) Trifluoroacetonitrile oxide, formed from the oxime with PIDA, adds to allylbenzene; single example.[67]
Other heterocycles
The review lists further cyclisations, including:[60]
- 2H-azirines from enamines, with PIDA;
- indoles from N‑aryl enamines with PIDA (C–C bond formation) and from enamines with PIFA (C–N bond formation);
- oxazoles from propargylamides, with PIDA in acetic acid;
- 2‑benzimidazolones and 2‑benzoxazolones from anthranilamides and salicylamides, with PIDA and KOH;
- spirooxindoles from anilides, with PIFA in trifluoroethanol.
Koser’s reagent gives heterocycles via the α-tosyloxy ketones of section 2. Ketones, Koser’s reagent and thioureas give 4‑substituted 2‑aminothiazoles in one pot in refluxing acetonitrile, a variant of the Hantzsch synthesis. The products are obtained as tosylate salts, which are converted into the free bases with sodium bicarbonate.[68]
Practical points
| Reaction | What the sources report |
|---|---|
| N‑Acylhydrazone to 1,3,4‑oxadiazole | PIDA (1–2 equiv), dichloromethane, room temperature (10 minutes) or reflux (10–30 minutes); recrystallisation from ethanol or chromatography.[61] |
| Pyridylhydrazone to triazolopyridine | PIDA (1.1 equiv, added in portions), dichloromethane, room temperature, overnight; the residue is dissolved in warm ethanol and the solid formed on cooling is filtered.[63] |
| Thiobenzanilide to benzothiazole | PIFA, 2,2,2‑trifluoroethanol, room temperature, 30 minutes.[64] |
| Unsaturated N‑methoxy amide to hydroxy lactam | PIFA (1.2 equiv), trifluoroacetic acid (1 equiv), dichloromethane (0.15 M), 0 °C; then ammonia in methanol for 20 minutes.[65] |
| Aldoxime and alkene to isoxazoline | PIDA in methanol with catalytic trifluoroacetic acid;[66] for trifluoroacetaldoxime, dichloromethane with 2 equivalents each of oxime and PIDA.[67] |
| Ketone and thiourea to 2‑aminothiazole | Koser’s reagent, refluxing acetonitrile; sodium bicarbonate for the free base.[68] |
PIDA and PIFA mediate oxidative cyclisations that form C–O, C–N, C–S and C–C bonds, without a metal and mostly at or below room temperature. Acylhydrazones give 1,3,4‑oxadiazoles, pyridylhydrazones give triazolopyridines, thiobenzanilides give benzothiazoles, and unsaturated N‑methoxy amides give hydroxy lactams. PIDA also oxidises aldoximes to nitrile oxides for isoxazoline synthesis.
Products: PIDA · PIFA · Koser’s reagent
References (section 7)
- J. Sun, D. Zhang-Negrerie, Y. Du, K. Zhao. Hypervalent iodine reagents for heterocycle synthesis and functionalization. Rep. Org. Chem. 2016, 6, 25–45. doi:10.2147/ROC.S84894 (open access)
- O. Prakash, V. Sharma, H. Batra, N. Rani, P. K. Sharma, S. P. Singh. Hypervalent iodine mediated synthesis of heterocyclyl-1,3,4‑oxadiazoles. Indian J. Chem. 1998, 37B, 797–800. core.ac.uk (open access)
- Z. Shang, J. Reiner, J. Chang, K. Zhao. Oxidative cyclization of aldazines with bis(trifluoroacetoxy)iodobenzene. Tetrahedron Lett. 2005, 46, 2701–2704. doi:10.1016/j.tetlet.2005.02.067
- O. Prakash, K. Hussain, D. K. Aneja, C. Sharma, K. R. Aneja. A facile iodine(III)-mediated synthesis of 3-(3‑aryl-1-phenyl-1H-pyrazol-4-yl)-[1,2,4]triazolo[4,3‑a]pyridines via oxidation of 2-((3‑aryl-1-phenyl-1H-pyrazol-4-yl)methylene)-1-(pyridin-2-yl)hydrazines and their antimicrobial evaluations. Org. Med. Chem. Lett. 2011, 1, 1. doi:10.1186/2191-2858-1-1 (open access)
- N. K. Downer-Riley, Y. A. Jackson. Conversion of thiobenzamides to benzothiazoles via intramolecular cyclization of the aryl radical cation. Tetrahedron 2008, 64, 7741–7744. doi:10.1016/j.tet.2008.06.023
- D. J. Wardrop, E. G. Bowen, R. E. Forslund, A. D. Sussman, S. L. Weerasekera. Intramolecular oxamidation of unsaturated O-alkyl hydroxamates: a remarkably versatile entry to hydroxy lactams. J. Am. Chem. Soc. 2010, 132, 1188–1189. doi:10.1021/ja9069997
- B. A. Mendelsohn, S. Lee, S. Kim, F. Teyssier, V. S. Aulakh, M. A. Ciufolini. Oxidation of oximes to nitrile oxides with hypervalent iodine reagents. Org. Lett. 2009, 11, 1539–1542. doi:10.1021/ol900194v
- R. S. B. Gonçalves, M. Dos Santos, G. Bernadat, D. Bonnet-Delpon, B. Crousse. A one-pot synthesis of 3‑trifluoromethyl-2-isoxazolines from trifluoromethyl aldoxime. Beilstein J. Org. Chem. 2013, 9, 2387–2394. doi:10.3762/bjoc.9.275 (open access)
- See reference [13] (section 2).
8. Alkenes and alkynes
This section describes metal-free reactions of alkenes and alkynes: the syn or anti addition of two oxygen substituents to a double bond, and a ring expansion by one carbon atom with Koser’s reagent (Figure 15). The palladium-catalysed reactions of alkenes with PIDA are described in section 10.
Additions of nitrogen to alkenes are described in other sections: the reactions of N‑methoxy amides in section 7, and the rhodium-catalysed aziridination of unsaturated carbamates and sulfamates in section 6.
Diacetoxylation with PIDA and boron trifluoride: syn or anti
PIDA with boron trifluoride etherate adds two acetoxy groups across an alkene. Water determines the stereochemistry: in the presence of water the addition is syn, and in its absence it is anti (Figure 15a).[69]
The method is applicable to a broad range of alkenes, including electron-poor ones, and gives good to excellent yields and diastereoselectivities, so it is an alternative route to 1,2‑diols. Methyl cinnamate was diacetoxylated on a 5 g scale in a few hours with the same efficiency as on a small scale.[69]
A trapping study with PIDA and boron trifluoride etherate supports a cyclic 1,3‑dioxolan-2-yl cation as the intermediate. Water adds to position 2 of this cation, and the ring then opens with retention of configuration, as in the Woodward reaction. In the control experiments, cis-4-octene gave the meso hydroxy acetate and trans-4-octene the racemic one, and acetylation gave the corresponding diacetates.[70]
The diastereomer is selected by the presence or absence of water, with the same reagents.[69]
Koser’s reagent: ditosyloxylation and ring expansion
Koser’s reagent adds two tosyloxy groups across an alkene, and the addition is syn: cyclohexene gives cis-1,2‑bis(tosyloxy)cyclohexane.[71][72]
With an exocyclic alkene on a benzo-fused ring, Koser’s reagent in 95% methanol (methanol–water 95:5) induces an oxidative rearrangement that expands the ring by one carbon atom. 1‑Methylideneindane gave β-tetralone in 94% yield after 20 minutes at room temperature (Figure 15b).[73]
The same reaction gave the homologous ketones: 2‑benzosuberone in 99% yield and the eight-membered ketone in 87% yield. The authors describe Koser’s reagent as a more benign alternative to the thallium(III) reagents used previously for this ring expansion.[73]
In the procedure, the solid reagent is added to a small excess of the alkene, and the reaction is mildly exothermic. Before work-up, a drop of the mixture is tested with aqueous potassium iodide to confirm that the oxidant has been consumed.[73]
Figure 15. Reactions of alkenes. (a) Diacetoxylation with PIDA and boron trifluoride etherate: syn addition with water present, anti addition without water; general scheme for an (E)-alkene.[69] (b) Ring expansion of 1‑methylideneindane to β-tetralone with Koser’s reagent; single example.[73]
Alkynes
Terminal alkynes react with Koser’s reagent in chloroform to give alkynyl(phenyl)iodonium tosylates, (β-tosyloxyvinyl)(phenyl)iodonium tosylates, or a mixture of both. The outcome depends on the size of the alkyne substituent: alkynes with a substituent larger than isopropyl, such as tert-butyl or cyclohexyl, give only the alkynyliodonium salts.[74]
These iodonium salts are themselves reagents and are described in section 11. Alkynes also undergo the cyclisations of section 7, in which propargylamides give oxazoles with PIDA.[60]
Practical points
| Reaction | What the sources report |
|---|---|
| Diacetoxylation | PIDA with boron trifluoride etherate; syn addition with water, anti addition without water; 5 g of methyl cinnamate in a few hours.[69] |
| Conditions of the trapping study | PIDA (1.25 equiv), acetic acid, boron trifluoride etherate (2.5 equiv), dichloromethane, added at −80 °C and warmed to −40 °C.[70] |
| Ring expansion | Koser’s reagent (10 mmol) added to the alkene (11 mmol) in 95% methanol (40 mL), room temperature, 20 minutes; potassium iodide test for remaining oxidant; extraction and chromatography.[73] |
| Terminal alkynes | Koser’s reagent in chloroform; the size of the substituent determines which type of iodonium salt is formed.[74] |
With boron trifluoride etherate, PIDA diacetoxylates alkenes, syn in the presence of water and anti in its absence. Koser’s reagent gives syn ditosyloxylation and, with exocyclic alkenes on benzo-fused rings, ring expansion by one carbon atom. Terminal alkynes give alkynyliodonium salts with Koser’s reagent.
Products: PIDA · Koser’s reagent
References (section 8)
- W. Zhong, J. Yang, X. Meng, Z. Li. BF3·OEt2-promoted diastereoselective diacetoxylation of alkenes by PhI(OAc)2. J. Org. Chem. 2011, 76, 9997–10004. doi:10.1021/jo201752y
- M. Shimogaki, M. Fujita, T. Sugimura. Stereoselective formation of substituted 1,3‑dioxolanes through a three-component assembly during the oxidation of alkenes with hypervalent iodine(III). Molecules 2015, 20, 17041–17057. doi:10.3390/molecules200917041 (open access)
- G. F. Koser, L. Rebrovic, R. H. Wettach. Functionalization of alkenes and alkynes with [hydroxy(tosyloxy)iodo]benzene. Bis(tosyloxy)alkanes, vinylaryliodonium tosylates, and alkynylaryliodonium tosylates. J. Org. Chem. 1981, 46, 4324–4326. doi:10.1021/jo00334a057
- L. Rebrovic, G. F. Koser. Reactions of alkenes with [hydroxy(tosyloxy)iodo]benzene: stereospecific syn-1,2‑ditosyloxylation of the carbon–carbon double bond and other processes. J. Org. Chem. 1984, 49, 2462–2472. doi:10.1021/jo00187a032
- M. W. Justik, G. F. Koser. Application of [hydroxy(tosyloxy)iodo]benzene in the Wittig-ring expansion sequence for the synthesis of β-benzocycloalkenones from α-benzocycloalkenones. Molecules 2005, 10, 217–225. doi:10.3390/10010217 (open access)
- L. Rebrovic, G. F. Koser. Alkynylaryliodonium tosylates and aryl[β-(tosyloxy)vinyl]iodonium tosylates from reactions of terminal alkynes with [hydroxy(tosyloxy)iodo]benzene. J. Org. Chem. 1984, 49, 4700–4702. doi:10.1021/jo00198a022
9. Radical reactions
PIDA and PIFA also generate radicals. Alcohols and carboxylic acids bind to iodine as ligands, and the resulting iodine(III) species fragment into radicals under light.[79][82]
This section describes the functionalisation of remote C–H bonds by alkoxyl radicals, the decarboxylation of carboxylic acids and the Minisci alkylation of heteroarenes (Figure 16).
Alcohols: alkoxyl radicals and remote C–H functionalisation
With PIDA and iodine under visible light, an alcohol gives an alkoxyl radical. The radical abstracts a hydrogen atom from the δ-carbon through a six-membered transition state, and the products are 1,4‑iodohydrins and tetrahydrofurans (Figure 16a).[75][76]
The reaction proceeds at room temperature. In a typical procedure, the alcohol, PIDA and 1 equivalent of iodine in dichloromethane are irradiated with two 80 W tungsten lamps.[77]
The site of hydrogen abstraction can depend on the neighbouring substituent. In carbohydrate models, an electron-donating alkyl group favoured the six-membered transition state, whereas an electron-withdrawing acyl group shifted the abstraction to the next carbon.[77]
In one study of iodine(III) reagents, PIDA was the effective reagent for alcohols and PIFA for carboxylic acids.[78]
PIFA under blue light also converts free alcohols into alkoxyl radicals. PIFA is the only oxidant, and no photocatalyst is used. In the presence of an N‑heteroarene, the δ-carbon radical adds to the heteroarene, as in a Minisci reaction: n-pentanol and 4‑methylquinoline gave the δ-heteroarylated alcohol in 90% yield (Figure 16b).[79]
The δ-selectivity is maintained even when a more reactive benzylic C–H bond is present. Tertiary δ-C–H bonds also react and give quaternary carbon centres.[79]
Amides react analogously. With PIFA under visible light, a tosylamide and 4‑methylquinoline gave the remote C–H heteroarylation product in 85% yield, and no reaction occurred in the dark or on heating.[80]
Carboxylic acids: decarboxylation
With PIDA and iodine under light, carboxylic acids undergo decarboxylation to give alkyl iodides.[81][82]
An ESR study showed that both acetate groups of PIDA are first exchanged for the carboxylate. The iodine(III) dicarboxylate then fragments under light, and the alkyl radicals formed by decarboxylation were detected.[82]
With more PIDA, the alkyl iodide is oxidised further, and tertiary and benzylic acids give acetates. In dichloromethane–acetic acid (1:1) under ordinary room light, 3-(4‑bromophenyl)-2,2‑dimethylpropanoic acid gave the tertiary acetate in 73% NMR yield (Figure 16c), and ibuprofen and loxoprofen were acetoxylated efficiently at the benzylic carbon.[83]
Both iodine and light are required: without iodine no reaction occurred, and in the dark the yield was below 5%. A primary acid, dodecanoic acid, gave no product.[83]
The proposed mechanism has two stages. PIDA and iodine form acetyl hypoiodite, which converts the acid into an acyl hypoiodite, and light-induced decarboxylation gives the alkyl iodide. PIDA then oxidises this iodide to an alkyl iodane, in which the iodine group is replaced by acetate, likely through a cationic intermediate.[83]
Minisci alkylation with carboxylic acids
Alkyl radicals generated by decarboxylation with PIDA also add to protonated N‑heteroarenes. Irradiation of a carboxylic acid and PIDA in the presence of a protonated heteroaromatic base gives the alkylated base, in a general and mild variant of the Minisci reaction.[84]
Figure 16. Radical reactions. (a) An alcohol gives a 2‑substituted tetrahydrofuran through an alkoxyl radical and a 1,5‑hydrogen shift; general scheme.[75][76][77] (b) δ-C–H heteroarylation of an alcohol with PIFA under blue light; general scheme, with the yield of the model reaction with n-pentanol (R1 = methyl, R2 = H); the source does not state whether this is an isolated yield.[79] (c) Decarboxylative acetoxylation of a tertiary acid; single example, NMR yield.[83]
Practical points
| Reaction | What the sources report |
|---|---|
| Alcohol to tetrahydrofuran | PIDA and iodine (1 equiv) in dichloromethane at room temperature, irradiated with two 80 W tungsten lamps.[77] |
| δ-C–H heteroarylation of alcohols | Heteroarene (0.4 mmol), alcohol (5 equiv), PIFA (2.3 equiv), dichloromethane, 100 W blue LEDs, room temperature with fan cooling, under nitrogen; aqueous KOH in the work-up.[79] |
| Decarboxylative acetoxylation | PIDA and iodine in dichloromethane–acetic acid (1:1) under room light; no reaction without iodine, below 5% in the dark.[83] |
| Minisci alkylation | Carboxylic acid, PIDA and the protonated heteroaromatic base, irradiated.[84] |
| Choice of reagent | In one study, PIDA was the effective reagent for alcohols and PIFA for carboxylic acids.[78] |
With iodine and visible light, PIDA converts alcohols into alkoxyl radicals and carboxylic acids into alkyl radicals. Alkoxyl radicals functionalise the δ-C–H bond; alkyl radicals give iodides, acetates or, with a protonated heteroarene, Minisci products. PIFA alone under blue light generates alkoxyl radicals from free alcohols.
References (section 9)
- J. I. Concepción, C. G. Francisco, R. Hernández, J. A. Salazar, E. Suárez. Intramolecular hydrogen abstraction. Iodosobenzene diacetate, an efficient and convenient reagent for alkoxy radical generation. Tetrahedron Lett. 1984, 25, 1953–1956. doi:10.1016/S0040-4039(01)90085-1
- P. de Armas, J. I. Concepción, C. G. Francisco, R. Hernández, J. A. Salazar, E. Suárez. Intramolecular hydrogen abstraction. Hypervalent organoiodine compounds, convenient reagents for alkoxyl radical generation. J. Chem. Soc., Perkin Trans. 1 1989, 405–411. doi:10.1039/P19890000405
- C. G. Francisco, R. Freire, A. J. Herrera, I. Pérez-Martín, E. Suárez. Intramolecular 1,5- versus 1,6‑hydrogen abstraction reaction promoted by alkoxy radicals in carbohydrate models. Org. Lett. 2002, 4, 1959–1961. doi:10.1021/ol025981u
- H. Togo, T. Muraki, Y. Hoshina, K. Yamaguchi, M. Yokoyama. Formation and synthetic use of oxygen-centred radicals with (diacetoxyiodo)arenes. J. Chem. Soc., Perkin Trans. 1 1997, 787–794. doi:10.1039/A603446B
- X. Wu, H. Zhang, N. Tang, Z. Wu, D. Wang, M. Ji, Y. Xu, M. Wang, C. Zhu. Metal-free alcohol-directed regioselective heteroarylation of remote unactivated C(sp3)–H bonds. Nat. Commun. 2018, 9, 3343. doi:10.1038/s41467-018-05522-9 (open access)
- N. Tang, X. Wu, C. Zhu. Practical, metal-free remote heteroarylation of amides via unactivated C(sp3)–H bond functionalization. Chem. Sci. 2019, 10, 6915–6919. doi:10.1039/C9SC02564B (open access)
- J. I. Concepción, C. G. Francisco, R. Freire, R. Hernández, J. A. Salazar, E. Suárez. Iodosobenzene diacetate, an efficient reagent for the oxidative decarboxylation of carboxylic acids. J. Org. Chem. 1986, 51, 402–404. doi:10.1021/jo00353a026
- A. Alberti, M. Benaglia, E. Vismara. An ESR approach to hypervalent iodine induced iododecarboxylation. Res. Chem. Intermed. 1989, 11, 117–126. doi:10.1163/156856789X00023
- K. Kiyokawa, D. Okumatsu, S. Minakata. Hypervalent iodine(III)-mediated decarboxylative acetoxylation at tertiary and benzylic carbon centers. Beilstein J. Org. Chem. 2018, 14, 1046–1050. doi:10.3762/bjoc.14.92 (open access)
- F. Minisci, E. Vismara, F. Fontana, M. C. Nogueira Barbosa. A new general method of homolytic alkylation of protonated heteroaromatic bases by carboxylic acids and iodosobenzene diacetate. Tetrahedron Lett. 1989, 30, 4569–4572. doi:10.1016/S0040-4039(01)80747-4
10. PIDA as the oxidant in palladium catalysis
PIDA is used in palladium catalysis to oxidise palladium(II) to a higher oxidation state. A 2020 review concludes that most of these reactions proceed through palladium(II)/palladium(IV) cycles, in which oxidation by the iodine(III) reagent is the key step.[85]
This section describes three applications: directed C–H acetoxylation, C–H amination to carbazoles, and the difunctionalisation of alkenes (Figure 17).
Directed C–H acetoxylation
A nitrogen donor in the substrate, such as a pyridine or an oxime ether, coordinates to palladium(II) and directs it to a nearby C–H bond to form a palladacycle. PIDA oxidises the palladacycle to a high-valent palladium species, and the C–O bond is then formed by reductive elimination.[86]
Benzo[h]quinoline is acetoxylated in high yield as a single isomer (Figure 17a), and the reaction can be carried out without exclusion of air or moisture. In alcohol solvents such as methanol, isopropanol or trifluoroethanol, an ether is formed instead of the acetate.[86]
sp3 C–H bonds also react, with a preference for primary C–H bonds β to the directing group; in a trans-decalone O-methyl oxime ether, a secondary β-C–H bond reacted with high selectivity.[86]
The directed method was developed from an earlier, non-directed acetoxylation of arenes with palladium(II) acetate and PIDA.[86]
C–H amination: carbazoles at room temperature
N‑Substituted 2‑aminobiaryls cyclise to carbazoles with palladium(II) acetate and PIDA in toluene with acetic acid at room temperature (Figure 17b).[85] The yields are good to excellent, and carbazoles with complex structures can also be prepared.[87]
Figure 17. PIDA as the oxidant in palladium catalysis. (a) Directed C–H acetoxylation of benzo[h]quinoline; the source describes the yield as high and gives the full conditions only in a graphic.[86] (b) Carbazoles from N‑substituted 2‑aminobiaryls at room temperature; general scheme.[85][87]
Alkenes: aminoacetoxylation and acid-catalysed diacetoxylation
With palladium and PIDA, a nitrogen nucleophile and an acetate group add to an alkene. The first methods required two equivalents of alkene per nitrogen nucleophile. A later method with phthalimide uses the alkene as the limiting reagent, and in this method PIDA favours the trans-aminopalladation pathway.[85][88]
Not all reactions of PIDA with alkenes require a metal. PIDA alone reacts only slowly with alkenes, which is usually attributed to the low electrophilicity of its iodine atom.[90] For the diacetoxylation of alkenes, a mechanistic study found that protons are the catalyst, and triflic acid can be used in place of a metal catalyst.[89]
Practical points
| Reaction | What the sources report |
|---|---|
| Directed C–H acetoxylation | Palladium(II) acetate (catalytic) with PIDA; carried out without exclusion of air or moisture; alcohol solvents give ethers.[86] |
| Carbazoles | Palladium(II) acetate, PIDA, toluene, acetic acid, room temperature.[85][87] |
| Alkene aminoacetoxylation | Palladium catalyst, PIDA and phthalimide, with the alkene as the limiting reagent in the later method.[85][88] |
| Alkene diacetoxylation | Triflic acid as the catalyst; protons, not the metal, were found to be the catalytic species.[89] |
PIDA oxidises palladium(II) to a high-valent state, from which C–O and C–N bonds are formed. The applications include directed C–H acetoxylation, carbazole formation at room temperature and the aminoacetoxylation of alkenes. For alkene diacetoxylation, a Brønsted acid can replace the metal catalyst.
Product: PIDA
References (section 10)
- S. E. Shetgaonkar, F. V. Singh. Hypervalent iodine reagents in palladium-catalyzed oxidative cross-coupling reactions. Front. Chem. 2020, 8, 705. doi:10.3389/fchem.2020.00705 (open access)
- S. R. Neufeldt, M. S. Sanford. Controlling site selectivity in palladium-catalyzed C–H bond functionalization. Acc. Chem. Res. 2012, 45, 936–946. doi:10.1021/ar300014f
- J. A. Jordan-Hore, C. C. C. Johansson, M. Gulias, E. M. Beck, M. J. Gaunt. Oxidative Pd(II)-catalyzed C–H bond amination to carbazole at ambient temperature. J. Am. Chem. Soc. 2008, 130, 16184–16186. doi:10.1021/ja806543s
- C. Martínez, Y. Wu, A. B. Weinstein, S. S. Stahl, G. Liu, K. Muñiz. Palladium-catalyzed intermolecular aminoacetoxylation of alkenes and the influence of PhI(OAc)2 on aminopalladation stereoselectivity. J. Org. Chem. 2013, 78, 6309–6315. doi:10.1021/jo400671q
- Y.-B. Kang, L. H. Gade. The nature of the catalytically active species in olefin dioxygenation with PhI(OAc)2: metal or proton? J. Am. Chem. Soc. 2011, 133, 3658–3667. doi:10.1021/ja110805b
- T. H. Wöste, K. Muñiz. Enantioselective vicinal diacetoxylation of alkenes under chiral iodine(III) catalysis. Synthesis 2016, 48, 816–827. doi:10.1055/s-0035-1561313
11. Iodonium salts and iodonium ylides from PIDA and Koser’s reagent
PIDA and Koser’s reagent are also the usual precursors of iodine(III) compounds with two carbon ligands. In iodonium salts, iodine has two carbon ligands and a positive charge, with a counter-anion such as tosylate. In iodonium ylides, one of the two carbon ligands is a carbanion, usually stabilised by two carbonyl groups.[91][92]
These compounds are not strong oxidants.[93] They are used to transfer one carbon group: an aryl group, an alkynyl group or, from an ylide, a carbene. This section describes their formation from PIDA and Koser’s reagent and their applications (Figures 18 and 19).
Diaryliodonium salts
Koser’s reagent reacts with arenes to give unsymmetrical aryl(phenyl)iodonium tosylates (Figure 18a).[91] In the fluoroalcohols TFE and HFIP the reagent is more reactive, and various thiophenes gave thienyl(phenyl)iodonium salts in excellent yields, without harmful by-products.[34]
Koser’s reagent also reacts with aryltrimethylsilanes, aryltributylstannanes and arylboronic acids.[91]
PIDA converts arylboronic acids into diaryliodonium salts (Figure 18b). In this boron–iodane exchange, first reported in 1997, the arylboronic acid reacts with PIDA or another (diacetoxyiodo)arene and boron trifluoride etherate in dichloromethane at room temperature; aqueous sodium tetrafluoroborate then gives the tetrafluoroborate salt.[91][94]
The exchange has become a standard method for the synthesis of symmetrical and unsymmetrical diaryliodonium salts, but electron-poor arylboronic acids give low yields.[94]
Applications of diaryliodonium salts
A diaryliodonium salt transfers one aryl group to a nucleophile, and the other aryl group is released as an aryl iodide. Without a metal catalyst, the salts arylate O-, N-, S- and C‑nucleophiles, as well as fluoride-18 for PET imaging.[91][95]
In an unsymmetrical salt, the nucleophile usually attacks the more electron-poor aryl group. The electron-rich 2,4,6‑trimethoxyphenyl group, introduced with 1,3,5‑trimethoxybenzene, therefore remains on iodine as a non-transferable (“dummy”) group, and only the other aryl group is transferred (Figure 18d).[95]
With metal catalysts, the scope is wider. Copper catalysts are used for the arylation of enolates, thiophenes, tetrazoles, nucleosides, anilines and phenols. With palladium, diaryliodonium salts phenylate C–H bonds of 2‑phenylpyridines and indoles through a proposed palladium(II)/palladium(IV) cycle, as in section 10.[91]
Figure 18. Iodonium salts from Koser’s reagent and PIDA. (a) Aryl(phenyl)iodonium tosylates from arenes; general scheme.[34][91] (b) Boron–iodane exchange with an arylboronic acid; general scheme.[91][94] (c) Alkynyl(phenyl)iodonium tosylates from terminal alkynes; general scheme for substituents larger than isopropyl.[74][91] (d) Metal-free arylation with an aryl(2,4,6‑trimethoxyphenyl)iodonium salt; the trimethoxyphenyl group remains on iodine; general scheme.[95]
Alkynyl(phenyl)iodonium salts
Alkynyl(phenyl)iodonium tosylates are commonly prepared by gentle heating of Koser’s reagent with a terminal alkyne in chloroform or dichloromethane (Figure 18c).[91] As described in section 8, the size of the alkyne substituent determines whether the alkynyl salt or the (β-tosyloxyvinyl) salt is formed.[74]
These salts transfer the alkynyl group. The aryl group is not transferred, but one study found that it strongly affects the reactivity and the stability of the salt.[93] A nucleophile undergoes conjugate addition to the alkyne to form a carbene. The carbene then either rearranges to a new alkyne, which corresponds to alkynylation of the nucleophile, or undergoes 1,5‑C–H insertion to form a ring.[93]
Enolates and amide anions have been alkynylated with these salts,[91] and a sulfinate was the nucleophile in the study mentioned above.[93] The salts also give heterocycles: imidazo[1,2‑a]pyridines with 2‑aminopyridine, and 2,4‑disubstituted thiazoles with thioureas or thioamides.[91]
Iodonium ylides
In the iodonium ylides of dicarbonyl compounds, iodine is bonded to a phenyl group and the carbanion. X-ray structures show a C–I–C angle near 90°, which indicates a zwitterionic C–I bond, so the ylides are drawn here with separated charges.[92]
These ylides are generally prepared from PIDA and the dicarbonyl compound under basic conditions.[92] In an Organic Syntheses procedure, dimethyl malonate, PIDA and potassium hydroxide in acetonitrile at 0–5 °C gave the ylide, which was collected by filtration in 77% yield (single example, Figure 19a).[96]
Most iodonium ylides have low thermal stability.[92] The malonate ylide degrades slowly at room temperature, over about two weeks, but can be stored for months at −20 °C. Its degradation is exothermic, although it never caused an explosion in the authors’ work, and the ylide is poorly soluble and unstable in organic solvents.[96]
Differential scanning calorimetry indicated that this ylide is safer than dimethyl diazomalonate, which is explosive and shock sensitive.[96]
Cyclopropanation without diazo compounds
With rhodium(II) catalysts, iodonium ylides transfer a carbene to alkenes to give cyclopropanes, so no diazo compound is required.[92][96]
With rhodium(II) acetate (0.1 mol%) in an excess of the alkene or diene as the solvent, at 120 °C or at reflux, the malonate ylide gave cyclopropanes from alkenes and vinylcyclopropanes from dienes within minutes. Styrene gave the cyclopropane in 80% yield (single example), compared with 57% with copper(II) acetylacetonate. The reaction was stereospecific: a cis-alkene gave the cis-cyclopropane.[97]
With the dirhodium catalyst Rh2(esp)2 (0.02 mol%) in dichloromethane, the same ylide and styrene gave dimethyl 2‑phenylcyclopropane-1,1‑dicarboxylate in 92–95% yield (single example).[96]
Isolation of the ylide is not necessary. In a one-pot procedure, Meldrum’s acid, PIDA, rhodium(II) acetate, alumina and 4 Å molecular sieves were stirred in dichloromethane with an excess of the alkene at 30 °C. The racemic cyclopropanes were obtained in yields of up to 85% (Figure 19b).[98][99] With chiral rhodium(II) catalysts, enantiomeric excesses of up to 66% were obtained.[99]
The cyclopropanation with the Meldrum’s acid ylide is stereospecific, and with furan or 2,3‑dihydrofuran the ylide gave no 1,3‑cycloadducts.[100]
Figure 19. Iodonium ylides as carbene sources. (a) Formation of the dimethyl malonate ylide with PIDA, and rhodium-catalysed cyclopropanation of styrene with this ylide; single examples.[96] (b) One-pot cyclopropanation with Meldrum’s acid, PIDA and rhodium(II) acetate; general scheme, racemic products.[98]
Iodonium ylides have further applications. In rhodium-catalysed reactions with dienes and α,β-unsaturated carbonyl compounds they give dihydrofurans and other heterocycles. Spirocyclic ylides are used for radiofluorination in PET chemistry, and a trifluoromethanesulfonyl ylide is a reagent for trifluoromethylthiolation.[92]
Practical points
| Reaction | What the sources report |
|---|---|
| Aryl(phenyl)iodonium tosylates | Koser’s reagent with an arene; with thiophenes, TFE or HFIP gave excellent yields.[34][91] |
| Diaryliodonium tetrafluoroborates | Arylboronic acid, PIDA and boron trifluoride etherate in dichloromethane at room temperature, then aqueous sodium tetrafluoroborate; electron-poor arylboronic acids give low yields.[91][94] |
| Alkynyl(phenyl)iodonium tosylates | Koser’s reagent and the terminal alkyne in chloroform or dichloromethane, gentle heating; with a substituent larger than isopropyl, only the alkynyl salt is formed.[74][91] |
| Storage of alkynyl(aryl)iodonium tosylates | All the salts in one study were stable indefinitely at −20 °C. At 30 °C, the 2‑anisyl salt was unchanged after seven days, and the other salts decomposed within minutes.[93] |
| Malonate ylide | PIDA (1.1 equiv), potassium hydroxide (5 equiv), acetonitrile, 0–5 °C, 2 hours; collected by filtration, washed with water and diethyl ether, dried under vacuum at 30 °C; 77%.[96] |
| Storage of the malonate ylide | Stable for months at −20 °C; slow degradation at room temperature; an oily solid indicates an incorrect work-up or incomplete drying.[96] |
| Cyclopropanation with the isolated ylide | Rhodium(II) acetate (0.1 mol%), the alkene or diene in excess as the solvent, 120 °C or reflux, minutes;[97] or Rh2(esp)2 (0.02 mol%) in dichloromethane.[96] |
| One-pot cyclopropanation | Meldrum’s acid, PIDA (1.4 equiv), rhodium(II) acetate (5 mol%), alumina (2.3 equiv), 4 Å molecular sieves, dichloromethane, alkene (10 equiv), 30 °C.[98] |
PIDA and Koser’s reagent are the usual precursors of iodonium salts and iodonium ylides. Diaryliodonium salts transfer an aryl group, alkynyl(phenyl)iodonium salts transfer an alkynyl group, and the ylides of malonates and Meldrum’s acid give cyclopropanes with rhodium catalysts, without diazo compounds.
Products: PIDA · Koser’s reagent · Rhodium(II) acetate · Meldrum’s acid · 1,3,5‑Trimethoxybenzene · Arylboronic acids
References (section 11)
- M. S. Yusubov, A. V. Maskaev, V. V. Zhdankin. Iodonium salts in organic synthesis. ARKIVOC 2011, (i), 370–409. doi:10.3998/ark.5550190.0012.107 (open access)
- M. S. Yusubov, A. Yoshimura, V. V. Zhdankin. Iodonium ylides in organic synthesis. ARKIVOC 2016, (i), 342–374. doi:10.3998/ark.5550190.p009.732 (open access)
- D. J. Hamnett, W. J. Moran. Improving alkynyl(aryl)iodonium salts: 2‑anisyl as a superior aryl group. Org. Biomol. Chem. 2014, 12, 4156–4162. doi:10.1039/c4ob00556b (open access)
- S. S. Karandikar, D. R. Stuart. Refining boron–iodane exchange to access versatile arylation reagents. Chem. Commun. 2022, 58, 1211–1214. doi:10.1039/D1CC06341C
- D. R. Stuart. Aryl(2,4,6‑trimethoxyphenyl)iodonium salts as reagents for metal-free arylation of carbon and heteroatom nucleophiles. TCIMAIL 2017, No. 173. tcichemicals.com (open access)
- S. R. Goudreau, D. Marcoux, A. B. Charette. Synthesis of dimethyl 2‑phenylcyclopropane-1,1‑dicarboxylate using an iodonium ylide derived from dimethyl malonate. Org. Synth. 2010, 87, 115–125. orgsyn.org (open access)
- G. Georgakopoulou, C. Kalogiros, L. P. Hadjiarapoglou. Rh(II)-catalyzed thermal cyclopropanations of a phenyliodonium bis(carbomethoxy)methylide with alkenes and dienes. Synlett 2001, 1843–1846. doi:10.1055/s-2001-18750
- A. Ghanem, F. Lacrampe, H. Y. Aboul-Enein, V. Schurig. Diazo compounds and phenyliodonium ylides in inter- and intramolecular cyclopropanations catalyzed by dirhodium(II). Synthesis and chiral resolution by GC versus HPLC. Monatsh. Chem. 2005, 136, 1205–1219. doi:10.1007/s00706-005-0299-6
- A. Ghanem, H. Y. Aboul-Enein, P. Müller. One-pot synthesis and chiral analysis of cyclopropane derivatives. Chirality 2005, 17, 44–50. doi:10.1002/chir.20093
- P. Müller, Y. Allenbach, E. Robert. Rhodium(II)-catalyzed olefin cyclopropanation with the phenyliodonium ylide derived from Meldrum’s acid. Tetrahedron: Asymmetry 2003, 14, 779–785. doi:10.1016/S0957-4166(03)00029-6
12. Deprotection, oxidation of sulfides and cleavage of diols
This section describes the cleavage of thioacetals and p‑methoxybenzyl (PMB) ethers, the oxidation of sulfides to sulfoxides, and the oxidative cleavage of 1,2‑diols and alkenes to carbonyl compounds (Figure 20).
Cleavage of dithianes and other thioacetals
Thioacetals such as 1,3‑dithianes are protecting groups for aldehydes and ketones, and the anions of 1,3‑dithianes are used as acyl anion equivalents. Thioacetals are stable to acids and bases, so regeneration of the carbonyl compound is often difficult, and many of the older methods use mercury or other metal salts.[101]
PIFA cleaves 1,3‑dithianes in aqueous acetonitrile or aqueous methanol (Figure 20a). Esters, alcohols, halides, secondary amides, acetals, alkenes and alkynes are tolerated, and the method has been widely used.[101][102]
PIDA also cleaves dithianes.[103] With PIFA, dithiane-containing alkaloids gave the corresponding amino ketones, and purification without chromatography made the procedure suitable for labile alkaloids.[104]
These hypervalent iodine methods require water and are therefore not applicable to substrates with water-sensitive groups. An anhydrous method with iodosylbenzene in dichloromethane has been reported; in that study, isotope labelling indicated that the oxygen atom of the new carbonyl group originates from the iodine reagent.[101]
Cleavage of PMB ethers
PIFA is the co-oxidant in a catalytic deprotection of PMB ethers. The catalyst is a nitroxyl radical with electron-withdrawing ester groups adjacent to the nitroxyl group. With 1 equivalent of PIFA the PMB group is removed (Figure 20b); with an excess of PIFA the PMB-protected alcohols are oxidised to the corresponding carbonyl compounds.[105]
Sulfides to sulfoxides
Iodine(III) reagents, including (diacyloxyiodo)benzenes such as PIDA and Koser’s reagent, oxidise sulfides selectively to sulfoxides.[106] In water, PIDA (1.1 equiv) with potassium bromide (0.1 equiv) oxidised alkyl aryl, benzyl methyl and diaryl sulfides at room temperature in 0.5–5 hours to give the sulfoxides in 82–96% yield (Figure 20c).[106]
Over-oxidation was minor: small amounts of sulfone were formed in some cases, for example 6% from methyl p‑tolyl sulfide. For diaryl sulfides with a cyano or nitro group, 1.5 equivalents of PIDA were used.[106]
Section 6 describes the related transfer of an NH group to sulfur, which gives sulfoximines.
Oxidative cleavage of 1,2‑diols and alkenes
PIDA in dichloromethane cleaves 1,2‑diols cleanly to aldehydes (Figure 20d).[107]
Alkenes are cleaved in one pot: catalytic osmium tetroxide, N‑methylmorpholine N‑oxide (NMO), 2,6‑lutidine and PIDA in acetone–water give the corresponding carbonyl compounds (Figure 20e). Without NMO, α-hydroxy ketones were formed as by-products in some cases.[107]
Figure 20. Deprotection, sulfur oxidation and diol cleavage. (a) Removal of a 1,3‑dithiane with PIFA; general scheme.[101][102] (b) Removal of a PMB ether with a nitroxyl radical catalyst and PIFA; general scheme.[105] (c) Diphenyl sulfide to diphenyl sulfoxide with PIDA and potassium bromide in water; single example.[106] (d) Cleavage of a 1,2‑diol with PIDA; general scheme.[107] (e) One-pot cleavage of an alkene; general scheme.[107]
Practical points
| Reaction | What the sources report |
|---|---|
| Dithianes with PIFA | Aqueous acetonitrile or aqueous methanol; esters, alcohols, halides, secondary amides, acetals, alkenes and alkynes tolerated.[101][102] |
| Dithianes with PIDA | PIDA used in place of PIFA.[103] |
| Labile amino ketones | PIFA, then purification without chromatography.[104] |
| PMB ethers | Nitroxyl radical catalyst with ester groups adjacent to the nitroxyl group; PIFA (1 equiv) removes the PMB group, an excess of PIFA gives the carbonyl compound.[105] |
| Sulfides to sulfoxides | PIDA (1.1 equiv), potassium bromide (0.1 equiv), water, room temperature, 0.5–5 hours; extraction with ethyl acetate and chromatography; 1.5 equivalents of PIDA for diaryl sulfides with a cyano or nitro group.[106] |
| 1,2‑Diols | PIDA in dichloromethane.[107] |
| Alkenes | Osmium tetroxide (catalytic), NMO, 2,6‑lutidine and PIDA in acetone–water.[107] |
PIFA and PIDA convert dithianes into the parent carbonyl compounds without mercury salts. With catalytic potassium bromide in water, PIDA oxidises sulfides to sulfoxides with little over-oxidation to the sulfone, and in dichloromethane it cleaves 1,2‑diols to aldehydes.
Products: PIFA · PIDA · Koser’s reagent
References (section 12)
- Z. Yu, Y. Ouyang, X. Wang, B. Zhao, X. Wang, Y. Du, K. Zhao. PhIO-mediated oxidative dethioacetalization/dethioketalization under water-free conditions. Arkivoc 2021, (vii), 48–65. doi:10.24820/ark.5550190.p011.526 (open access)
- G. Stork, K. Zhao. A simple method of dethioacetalization. Tetrahedron Lett. 1989, 30, 287–290. doi:10.1016/S0040-4039(00)95181-5
- X.-X. Shi, Q.-Q. Wu. Deblocking of dithianes with diacetoxyiodobenzene. Synth. Commun. 2000, 30, 4081–4086. doi:10.1080/00397910008087023
- F. F. Fleming, L. Funk, R. Altundas, Y. Tu. Deprotecting dithiane-containing alkaloids. J. Org. Chem. 2001, 66, 6502–6504. doi:10.1021/jo0157829
- S. Hamada, K. Sugimoto, E. E. Elboray, T. Kawabata, T. Furuta. Chemoselective oxidation of p‑methoxybenzyl ethers by an electronically tuned nitroxyl radical catalyst. Org. Lett. 2020, 22, 5486–5490. doi:10.1021/acs.orglett.0c01839
- H. Tohma, T. Maegawa, Y. Kita. Facile and efficient oxidation of sulfides to sulfoxides in water using hypervalent iodine reagents. ARKIVOC 2003, (vi), 62–70. doi:10.3998/ark.5550190.0004.608 (open access)
- K. C. Nicolaou, V. A. Adsool, C. R. H. Hale. An expedient procedure for the oxidative cleavage of olefinic bonds with PhI(OAc)2, NMO, and catalytic OsO4. Org. Lett. 2010, 12, 1552–1555. doi:10.1021/ol100290a
13. Choice of reagent, handling and work-up
The three reagents are iodine(III) compounds with the same core: iodine bonded to a phenyl group and two oxygen ligands. PIDA has two acetate ligands, PIFA two trifluoroacetate ligands, and Koser’s reagent a hydroxy and a tosyloxy ligand (Scheme 1, at the start of the article).
The hypervalent three-centre bond is responsible for their high electrophilic reactivity.[108] Iodine(III) compounds are T-shaped, and the most electronegative ligands form the hypervalent bond in an approximately linear arrangement through iodine.[109]
Choice of reagent
PIDA is the reagent used in most reactions in this article: alcohol oxidation with TEMPO (section 1), phenol dearomatisation (section 3), nitrogen transfer (section 6), alkene diacetoxylation (section 8), alkoxyl radicals (section 9), palladium catalysis (section 10), iodonium ylides (section 11), and sulfide and diol oxidation (section 12). Acyclic bis(acyloxy)iodoarenes such as PIDA are stable solids that can be stored for long periods.[108]
PIDA and PIFA differ in reactivity. PIFA reacts with alkenes without an additive or catalyst,[108] whereas PIDA alone reacts only slowly with alkenes.[90] In this article, PIFA is used for the formation of arene radical cations and biaryl coupling (section 4), for the Hofmann rearrangement under mildly acidic conditions (section 5)[45] and for the cleavage of dithianes (section 12).
PIFA releases trifluoroacetic acid, which is a much stronger acid than the acetic acid released by PIDA.
Koser’s reagent is used to introduce a tosyloxy group, as in the α-tosyloxylation of ketones (section 2) and the syn ditosyloxylation of alkenes (section 8), and to prepare aryl- and alkynyliodonium salts (section 11). It is also used in the Hofmann rearrangement (section 5) and in heterocycle synthesis (section 7).
Solvents and additives
Fluoroalcohols change the reactivity of the reagents. In HFIP, PIFA oxidises electron-rich arenes to radical cations (section 4), and in TFE or HFIP Koser’s reagent is more reactive and gives iodonium salts with thiophenes (section 11).[33][34]
Boron trifluoride etherate activates PIFA for biaryl coupling (section 4) and PIDA for alkene diacetoxylation (section 8).[38][69]
Handling and storage
The table lists the data from the product pages and the safety data sheets supplied with each product.
| PIDA | PIFA | Koser’s reagent | |
|---|---|---|---|
| Form | White to light yellow crystalline powder | White to light yellow powder or crystals | White to light yellow powder or crystals |
| Melting point | 161–163 °C | 123–127 °C | 136–142 °C |
| Soluble in | Acetic acid, acetonitrile, dichloromethane; reacts with water | Dichloromethane, THF, DMF; insoluble in water | Methanol, DMSO, hot acetonitrile; moderately soluble in water; largely insoluble in dichloromethane, chloroform and cold acetonitrile |
| Storage | Sealed, dry and dark, at room temperature | Tightly closed and dry, under inert gas, at 2–8 °C, protected from light | Tightly sealed and protected from light, at room temperature |
| Hazard (GHS) | Warning: skin and eye irritation (H315, H319) | Warning: skin, eye and respiratory irritation (H315, H319, H335) | Warning: skin and eye irritation (H315, H319) |
| Hazardous combustion products | Carbon oxides, hydrogen iodide | Carbon oxides, hydrogen iodide, hydrogen fluoride | Carbon oxides, hydrogen iodide |
In a study by thermogravimetry and differential scanning calorimetry, PIDA, PIFA, Koser’s reagent and a related reagent lost mass mainly in one step and decomposed endothermically.[110]
Iodosylbenzene, mentioned in section 12, behaves differently: on heating or prolonged storage at room temperature it disproportionates to iodobenzene and explosive iodylbenzene, and a violent explosion of a sample dried at 110 °C under vacuum has been reported.[108] Most iodonium ylides (section 11) also have low thermal stability.[92]
Work-up
In most reactions in this article the reagent is reduced to iodobenzene, so one equivalent of iodobenzene has to be separated from the product; in the iodonium salts and ylides of section 11, the iodine remains in the product. The ligands are either released as the corresponding acid or incorporated into the product, as in diacetoxylation and tosyloxylation.
With polymer-supported, fluorous or ionic-liquid-supported versions of these reagents, the reduced iodoarene can be removed by filtration or extraction, but polymer-bound reagents are often less reactive than their monomeric analogues.[108]
PIDA is used in most of the reactions in this article. PIFA is used for arene radical cations, biaryl coupling, the Hofmann rearrangement under mildly acidic conditions and dithiane cleavage, and Koser’s reagent for the introduction of tosyloxy groups and the synthesis of iodonium salts. PIFA is stored at 2–8 °C, dry and under inert gas; PIDA and Koser’s reagent are stored sealed and protected from light at room temperature.
Products: PIDA · PIFA · Koser’s reagent
References (section 13)
- V. V. Zhdankin. Hypervalent iodine(III) reagents in organic synthesis. ARKIVOC 2009, (i), 1–62. doi:10.3998/ark.5550190.0010.101 (open access)
- A. Greener, S. P. Argent, C. J. Clarke, M. L. O’Duill. Structure and thermal stability of phosphorus-iodonium ylids. Beilstein J. Org. Chem. 2024, 20, 2931–2939. doi:10.3762/bjoc.20.245 (open access)
- V. Verma, K. Singh, A. Kumar, D. Kumar. Thermal studies of hypervalent iodine reagents. J. Therm. Anal. Calorim. 2013, 114, 339–344. doi:10.1007/s10973-012-2894-1
Products in this article
The table lists the NorrChemica products named in this article, with the use of each product and the sections that describe it.
| Product | CAS number | Purity | Use in this article | Sections |
|---|---|---|---|---|
| PIDA, (diacetoxyiodo)benzene | 3240-34-4 | ≥97% | Oxidant in alcohol oxidation with TEMPO, phenol dearomatisation, nitrogen transfer, alkene diacetoxylation, radical reactions and palladium catalysis; precursor of iodonium salts and ylides | 1, 2, 3, 5, 6, 7, 8, 9, 10, 11, 12 |
| PIFA, [bis(trifluoroacetoxy)iodo]benzene | 2712-78-9 | ≥97% | Oxidant for phenols and electron-rich arenes, biaryl coupling, the Hofmann rearrangement, oxidative cyclisations, radical reactions, and the cleavage of dithianes and PMB ethers | 3, 4, 5, 6, 7, 9, 12 |
| Koser’s reagent (HTIB), [hydroxy(tosyloxy)iodo]benzene | 27126-76-7 | ≥96% | α-Tosyloxylation of ketones, Hofmann rearrangement to ammonium tosylates, ditosyloxylation and ring expansion of alkenes, synthesis of iodonium salts | 2, 4, 5, 7, 8, 11, 12 |
| TEMPO | 2564-83-2 | ≥97% | Catalyst for the oxidation of alcohols with PIDA | 1 |
| 4‑Acetamido-TEMPO | 14691-89-5 | ≥98% | Mediator in the electrochemical oxidation of nucleosides to 5′-carboxylic acids | 1 |
| Rhodium(II) acetate | 5503-41-3 | 95% | Catalyst for C–H amination with PIDA and for cyclopropanation with iodonium ylides | 6, 11 |
| Meldrum’s acid | 2033-24-1 | ≥98% | Ylide precursor in the one-pot cyclopropanation with PIDA | 11 |
| 1,3,5‑Trimethoxybenzene | 621-23-8 | ≥98% | Source of the non-transferable 2,4,6‑trimethoxyphenyl group in diaryliodonium salts | 11 |
| Arylboronic acids (collection) | – | – | Substrates for the boron–iodane exchange with PIDA, which gives diaryliodonium salts | 11 |
Hypervalent iodine reagents from NorrChemica
Pack sizes, prices and safety data sheets are on the product pages. Shipped from Finland, with DDP delivery worldwide.
- PIDA, ≥97%CAS 3240-34-4
- PIFA, ≥97%CAS 2712-78-9
- Koser’s reagent, ≥96%CAS 27126-76-7
About this article. The article is based on the 109 publications listed after each section. Fifty of them were read as full text, author version or supporting information, in whole or for the passages cited. The other 59 were available only as abstracts, summaries or citations in other papers, and the statements cited to them are limited to what those texts state. All statements, structures and reference details were checked a second time against the sources that could be opened again. The handling, storage and hazard data come from the NorrChemica product pages and their safety data sheets. Sources read on 17 and 18 November 2026. This article is a guide to the literature, not a laboratory protocol.
© 2026 NorrChemica. All rights reserved.
Content may not be reproduced without written permission.